background image

DSP

EAKER

 S

ERVO

 300

Table of contents

1 Connections and Buttons..................................................................................................4

1.1 Rear Panel:...................................................................................................................4
1.2 Front Side.....................................................................................................................5

2 Quick Set­up Guide............................................................................................................6

2.1 Usage...........................................................................................................................8

2.1.1 Control Button.....................................................................................................8
2.1.2 Status LED..........................................................................................................8
2.1.3 Input Gain Control...............................................................................................8
2.1.4 Automatic Wake­up and Stand­by......................................................................9

2.2 Errors and Warnings.....................................................................................................9

2.2.1 Blinking Red Status LED....................................................................................9
2.2.2 Status LED is Lit Red.........................................................................................9
2.2.3 Thermal Shut­down..........................................................................................10

2.3 Placing the Servo 300 Speaker..................................................................................10
2.4 Anti­ModeTM: Automatic Room Correction................................................................10
2.5 ASCM Calibration........................................................................................................11
2.6 Output Gain Switch.....................................................................................................12

3 Measurements..................................................................................................................13
4 Technical specification....................................................................................................14
5 Manufacturer.....................................................................................................................14
6 Support.............................................................................................................................14

Rev. 1.6

21.06.2010

Page 3 (16)

Summary of Contents for Servo 300

















Reviews: