manualshive.com logo in svg

DSE DSEPOWER DSE871 Series, Manual

Share
Download
DSE DSEPOWER DSE871 Series Manual Download Page 35

Controls and Indications 

 

Part No. 057-129   DSE871x mono remote display ISSUE 2.1  21/09/2010 ADM    

35

 

 
Transfer to generator (DSE8710/8711 only) 
 
Allows the operator to transfer the load to the generator, synchronising first if required. (when in 
Manual mode only) 

 

Open generator (DSE8710/8711 only) 
 
Allows the operator to open the generator breaker (when in Manual mode only) 

 

Close mains (DSE8760/8716 only) 
This push button is used to control the closure of the mains load switching device and has two modes 
of operation : 
1.  Synchronising is NOT enabled. Pressing this button when the mains is available off load and in 

MANUAL mode, the bus load switch is opened and the mains load switch is closed. Further 
presses of this button will have no effect. 

2.  Synchronising is enabled. Pressing this button when the mains is available and in MANUAL 

mode, the 8760 controller, will volts match and synchronise with the Bus. The mains load switch 
is then closed in parallel with the Bus.  

 

NOTE:

NOTE:

NOTE:

NOTE:----    This button is only active in MANUAL mode.

This button is only active in MANUAL mode.

This button is only active in MANUAL mode.

This button is only active in MANUAL mode.    

 

NOTE:

NOTE:

NOTE:

NOTE:----    If the bus is live when the manual button is pressed, synchronising will take 

If the bus is live when the manual button is pressed, synchronising will take 

If the bus is live when the manual button is pressed, synchronising will take 

If the bus is live when the manual button is pressed, synchronising will take 

place before the load

place before the load

place before the load

place before the load    switch is closed.

switch is closed.

switch is closed.

switch is closed.    

 

Close bus (DSE8760/8716 only) 
This push button is used to control the closure of the bus load switching device and has two modes of 
operation : 
3.  Synchronising is NOT enabled. Pressing this button when the bus is off load and in MANUAL 

mode, the mains load switch is opened and the bus load switch is closed. Further presses of this 
button will have no effect. 

4.  Synchronising is enabled. Pressing this button when the bus is live and in MANUAL mode, the 

8760 controller, will volts match and synchronise with the Mains. The bus load switch is then 
closed in parallel with the mains.  

 

NOTE:

NOTE:

NOTE:

NOTE:----    This button is only active in MANUAL mode.

This button is only active in MANUAL mode.

This button is only active in MANUAL mode.

This button is only active in MANUAL mode.    

 

NOTE:

NOTE:

NOTE:

NOTE:----    If the bus is live when the manual button is pressed, synchronising will tak

If the bus is live when the manual button is pressed, synchronising will tak

If the bus is live when the manual button is pressed, synchronising will tak

If the bus is live when the manual button is pressed, synchronising will take 

e 

e 

e 

place before the load switch is closed.

place before the load switch is closed.

place before the load switch is closed.

place before the load switch is closed.    

 

 

Menu navigation 
 
Used for navigating the instrumentation, event log and configuration screens.  
For further details, please see the more detailed description of these items elsewhere in this manual. 

 

 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Summary of Contents for DSEPOWER DSE871 Series





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands