background image

- 6 -

AUX

Connect to Any Device - Smart Phone, Tablet, Laptop, MP4/MP3 & Much More!

System 4

Level Matching

If you have ever listened to car audio system and heard lots of hiss, clicks or pops, then 
you have experienced and improperly level matched system. When a car audio system 
is properly level matched, you should get the maximum output from your source unit and 
amplifiers without any hiss, clicks or pops. The following steps will help you;

   1.  Set your source units fader and balance controls to their center positions. If your 
source unit  has  subwoofer output (and you are using it), set the output level at minimum. 

    2.  Disconnect the connections between your  KEQ20  and the amplifier(s).

    3. Start playing some relatively dynamic music and set the volume on your source unit 
to about 3/4 of maximum. You should not be hearing anything  at  this point. 

    4. Starting  with  the   KEQ20   Front Input gain control, increase or decrease the Input 
Gain control until the Overload LED begins to flicker steadily with the music. Do the same 
for the  Rear Input and Subwoofer Input.

Important Note:

For Four Channel Or Speaker Level Input Users. If you are only using the  Front  or  Rear

  

or  Speaker Level inputs, you will find that the subwoofer equalization now works on the 
rear channels. Therefore, the  Rear

 

 input gain is actually controlled by the  Subwoofer  

input gain control.

    5. Now adjust the output level control until the 2 volt or  5 volt  light starts to flicker.  You 
will set the output voltage to match up with your amplifiers input gain levels. 

    6. Double check that, the input gains on the amplifier(s) at minimum.
   

    7. Decrease the volume control on your source unit and re-connect the RCA's between 
the   KEQ20 and the amplifier(s).

    8.  Now increase the volume on your source unit to your normal listening level.
 

    9.  At this point you may find yourself going back and adjusting the Output Level controls 
on your   KEQ20  to balance the  Front,  Rear , and  Subwoofer sections of your system to 
accommodate for the speaker placement and efficiency.

Front 

Speakers

Rear

Speakers

Sub- 
woofers

Summary of Contents for KEQ20









Reviews: