manualshive.com logo in svg

DryGair DG-X, Installation, Operation And Maintenance Manual

Share
Download
DryGair DG-X Installation, Operation And Maintenance Manual Download Page 15

 

DryGair Dehumidification Unit Model DG-X 

 

Installation 

 

 

Ver. 12/2020 

 

9 

4.1.2 

Required Utilities 

Prepare the installation site before receiving the DryGair unit. 

•

 

Prepare a concrete leveled surface or hanging construction, built 
according to the unit dimensions and weight (see details in Appendix A). 

•

 

Prepare a 2-pole 40 Amp circuit breaker in a protected location near the 
unit. 

•

 

Prepare drainage for removing the water that is condensed by the unit. 
The unit is supplied with a short (1.5 m/5 feet) tube connected to a 1/2" 
BSP threaded plastic bushing. 

 

Warning 

The unit condensation water is not for drinking! 

 

•

 

If the unit is to be connected to a concrete ceiling, the site should be 
equipped with suitable climbing equipment to enable safe and 
comfortable access to the unit. 

•

 

The transit lanes inside the closed structure where the unit is to be 
installed must be kept clear, and the floor must be clean and free from 
any obstacles that might cause the forklift, truck, 

or crane to “jump”.

 

 

Summary of Contents for DG-X























































Reviews:

No comments

Brands by name

Popular brands

Load more brands