10
English
t r i o
-
i n s t r u c t i o n
f o r
i n s ta l l at i o n
7. Wireless remote control
The appliance is supplied with a wireless remote control.
Ignition, controlling the flame height and switching off are performed by a remote control that operates a receiver
in the control box.
User Manual, chapter 4, Command/control, describes the operation of the appliance including the way the remote
control works.
!Caution
Do not ignite the appliance before the gas and discharge connections have been fully installed, first observe the pro-
cedure described in chapter 8.3.
Below, we will describe how the receiver is connected.
7.1 Receiver
The receiver should be connected to the appliance, before the batteries are installed.
Follow the procedure below (
see Appendix 4,
Fig. 20
):
➠
Slide the brown plug of the connecting cable onto the back of the receiver’s printed circuit board.
➠
Connect the white plug to the gas control block.
!Tip
The plugs have different sizes that correspond with the connectors.
➠
Connect the cables of thermocouple 1 to the receiver; (
see Appendix 4, Fig. 20
, arrow B).
!Tip
- The size of the eye corresponds with the size of the screw;
- The colours of eye and screw also correspond.
➠
Connect the ignition cable to the receiver; (
see Appendix 4,
Fig. 20
, arrow A).
➠
Connect power:
a) When using batteries, see section 7.1.1 below;
b) When using an adapter:
- connect it to the receiver; (
see Appendix 4,
Fig. 20
, arrow C);
- insert the plug into the wall socket.
➠
Place the receiver in the control box, as indicated on
Fig. 18, see Appendix 4 (o)
.
➠
Bend the antenna out of the clips;
see Appendix 4,
Fig. 20
, arrow D and
Fig. 21
.
➠
Set the antenna straight.
!Caution
- Do not place the antenna too close to the ignition cable and/or metal parts (for the correct position,
see Appendix 4,
Fig. 21
);
- Do not place the ignition cable over and/or along metal parts: this will weaken the spark;
- Do not lay the ignition cable over the receiver. this could damage the receiver;
- Avoid dust on or in the receiver: cover it when performing work.
7.1.1 Placing / replacing the batteries
Follow the procedure below when placing the batteries:
➠
Open the door of the stove.
➠
Pick up the receiver.
➠
Slide the cover off.
➠
Place or remove the 4 penlite (AA type) batteries.
!Caution
- Avoid a short circuit between the batteries and metal objects/parts;
- Observe the “+” and “-” poles of the batteries and the holder;
- Use alkaline batteries.
➠
Slide back the cover.
➠
Place back the receiver.
!Caution
Batteries are regarded as “small chemical waste” and may therefore not be disposed with the household rubbish.
7.2 Setting the communication code
Prior to putting the application into operation, a communication code must be set between the remote control
and the receiver. If the receiver or the remote control are replaced, a new code will have to be set.
Follow the procedure described below:
➠
If necessary, place the batteries in the receiver’s battery holder; see section 6.1.1.
➠
If necessary, place the 9V block battery in the remote controle; see User Manual.
uk
Summary of Contents for G31 Propane
