22/29
9.4 SPECIAL FUNCTIONS:
1)
LCD CONTRAST ADJUSTMENT :
by Pressing ESC or OK during power on or immediately after a reset, you access the
menu for adjusting the contrast of LCD; hold down OK the contrast decreases, with ESC increases.
2)
FLOW TOTALIZER DATA VISUALIZATION: w
ith the VIP5 in standby mode, pressing the OK key will allow you to scroll
through the current average flow rate, or the total volume dispense in the last DAY, HOUR or TOTAL since last reset.
3)
RESETTING THE FLOW TOTALIZER: d
uring the visualization of the above parameters the flow can be reset by holding
the DOWN key.
4)
TIME AND DATE:
during standby, it is possible to view time and date by using the ESC key only if DATETIME
parameter is set on “enable”.
5)
EVENT LOG VIEWER:n
by holding the Up or Down key for five seconds it is possible to scroll through the Event Log .
( available in version FW 2.xx onwards)
DELAY TIM
5s
When the pressure switch is made, how long
to keep the pump running to ensure that the
signal is genuine and not a pressure spike
0s – 2min
X
X
x
x
x
With FLOW mode time an alarm condition
must exist before being reported
SUSPEND
Never
When the suspend signal is given to the
controller , we can have following values
Never – Do not stop
In Pause – Stop at the end of lubrication
phase
In Cycle – Stop during lubrication phase
Always – Stop when a signal is received
Never
In Pause
In Cycle
Always
X
X
X
X
X
SUSPEND T
Never
In Pulse Mode, will suspend the Lubrication
Phase if a signal is not received.
Null – 2min
X
X
X
X
X
PAUSE CNT
(Basic)
1
In Cycle Mode, set number of pulses during
pause phase. This mode can be used with.
If pause is zero will be based on “pause time”
setting.
Null – 250
(cycle mode)
Null-6000
(PULSE mode)
X
X
X
X
X
X
PAUSE MULTIP.
1
The ratio that can be applied for ‘pause
count’ setting, to allow the user to obtain a
higher counting breaks . ( eg., if pause is 52
and the multiplier is 100, the value will be
5200 )
1; 10; 100
X
X
X
X
X
CYCLE CNT
1
The Duration of the Lubrication cycle (in
PULSE Mode)
1-60000
X
X
X
X
X
FLOW VALUE
1,0
Informational value of how much lubricant is
dispensed per
Lubrication Cycle
0.0 - 1000
X
X
X
X
X
X
X
UNITS
Counts
Information Unit for the
flow value
parameter
used for display purposes only.
Counts,
CubicC., Liters, Pints,
Gallons, KilosGrams
X
X
X
X
X
X
X
FLOW MIN
10,0
Minimum Flow Setting
Totally excludes flow alarm if null
0.0 - 6000
X
FLOW MAX
100,0
Maximum Flow Setting
0.0 – 6000
X
MIN. LEV.
INPUT
NC
Configuration for the input signal of minimum
level
NC
NO
4-20mA
X
X
X
X
X
X
LO LEVEL MA
19,8
Setting a low level if you use 4-20mA input
4.0 – 20.0
X
X
X
X
X
X
HI LEVEL MA
4,2
Setting a high level if you use 4-20mA input
4.0 – 20.0
X
X
X
X
X
X
MININPUT
DELAY
0,5s
When resetting a low level alarm, grace period
before monitoring level inputs.
0s-5s
X
X
X
X
X
X
DATETIME
Disable
Enable or Disable the Real Time clock
functions. Note: be sure battery is connected.
Enable
Disable
X
X
X
X
X
X
X
DAY
1
DateTime: Day setting
1 – 31
X
X
X
X
X
X
X
MONTH
1
DateTime: Month setting
1 – 12
X
X
X
X
X
X
X
YEAR
2000
DateTime: Year setting
2000 - 2099
X
X
X
X
X
X
X
HOUR
0
DateTime: Hour setting
0 – 23
X
X
X
X
X
X
X
MINUTE
00
DateTime: Minute setting
0 – 59
SET DEFAULT
VAL.
RESET TO FACTORY DEFAULT SETTINGS
Yes – No
X
X
X
X
X
X
X
