CAMERA REPLACEMENT
1. Remove the Hovershot body. Please refer to the Control Board Replacement
section for details.
2. Unplug the camera cable.
3. Remove the 2 screws that secure the lens assembly to the body.
4. Remove the 4 screws that secure the camera board to the body.
Reverse these steps to install the new camera assembly.
BATTERY PRECAUTIONS
The Hovershot uses a lithium polymer (LiPo) battery. Follow these
precautions to ensure safe and trouble-free operation.
•
ALWAYS disconnect the battery from the quadcopter when not in use.
•
Do not attempt to use this charger with NiCd or NiMH battery packs.
•
Do not attempt to use a damaged battery.
•
This product contains a LiPo battery that must be recycled or disposed
of properly.
•
Do not leave the charger unattended while charging. Disconnect the
battery and unplug the charger immediately if either becomes hot!
However, it is normal for the charger to get warm.
•
Disconnect the battery from the charger and carefully move the
battery to a fi reproof location if the battery begins to swell or smoke!
•
Never allow the battery temperature to exceed 140° F [60° C].
•
Do not attempt to charge a battery if it is swollen or hot.
•
Do not place the charger or any battery on a fl ammable surface or
near combustible materials while in use.
•
Never disassemble or modify pack wiring in any way or puncture cells.
•
Never charge inside a vehicle.
•
Always disconnect the battery and unplug the charger when not in use.
•
Land your model immediately when the LEDs fl ash to indicate that the
battery power is low. Recharge the battery before attempting another
fl ight. A dangerous situation can occur when attempting to recharge
an over-discharged battery!
•
ALWAYS keep a supply of sand accessible when charging. Dumping
sand on the battery will extinguish a LiPo chemical fi re.
•
ALWAYS KEEP OUT OF REACH OF CHILDREN
SAFETY PRECAUTIONS
Follow these safety precautions when operating this or any model
quadcopter.
•
Adult supervision required.
•
Before fl ying, go to www.knowbeforeyoufl y.org.
•
Do not touch the spinning blades or fl y over another person’s head.
•
Keep your face and body as well as all spectators away from the
rotors whenever the battery is connected.
•
Stay clear of buildings, trees and power lines.
AVOID
fl ying in or near
crowded areas.
DO NOT
fl y close to people, children or pets.
•
Maintain a safe pilot-to-quadcopter distance while fl ying.
•
Your Hovershot quadcopter should not be considered a toy, but rather
a small, working model. If not operated correctly, the model could
possibly cause injury to you or spectators and damage to property.
•
You must check the operation of the model before every fl ight to
ensure that the model has remained structurally sound.
•
Do not alter or modify the model, as doing so may result in an unsafe
or unfl yable model.
•
Do your part in preserving the integrity of the FPV hobby. Know
the boundaries of your flying area and
ALWAYS
respect the privacy
of others.
90-DAY LIMITED WARRANTY
PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE.
Dromida will
repair or replace factory defects for 90 days from the date of purchase. This
warranty specifi cally does not cover crash damage, misuse or abuse. To make
a warranty claim, please contact our product support team at
1-217-398-
8970 option 6
or e-mail us at
. If requested
by Product Support, please send defective product to:
Hobby Services
3002 N Apollo Dr., Suite #1
Champaign, IL 61822
In the European Union, send it postpaid and insured to:
Service Abteilung Revell GmbH
Tel:
01805-110111
Henschelstrasse 20-30
(nur für Deutschland)
32257 Bünde Germany
E-mail: [email protected]
Please include a note about the problem, your contact information, and a
copy of the receipt.
This warranty applies only if the product is operated in compliance with the
instructions and warnings provided with each model. Dromida assumes no
liability except for the exclusive remedy or repair of parts as specifi ed above.
Dromida shall not be liable for consequential or incidental damages. Some
states do not allow the exclusion of consequential or incidental damages so
the above exclusion may not apply to you. This warranty gives you specifi c
legal rights and you may also have other rights which vary from state to state.
FCC IC PRECAUTIONS
IC RSS WARNING
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
IC RADIATION EXPOSURE STATEMENT
This equipment complies with IC RF radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
6
