DriSteem HUMIDI-TECH Installation, Operation And Maintenance Manual Download Page 2 | Manualshive

Page: 2 / 32

background image

2

TABLE OF CONTENTS

To the purchaser and installer

Thank you for purchasing our HUMIDI-TECH

®

humidifier. We have designed and built this equipment to give

you complete satisfaction and trouble-free service for many years. Familiarizing yourself with this manual will
help ensure proper operation of the equipment for years to come.

This manual covers the installation and maintenance procedures for both the HUMIDI-TECH and
HUMIDI-TECH DI humidifiers.

DRI-STEEM Humidifier Company

General information

Product overview ................................................................. 3
Dimensions .......................................................................... 4
Electrical specifications, capacities and weights ................. 5

Installation

Locating and mounting the humidifier .................................. 6
Piping ................................................................................... 6
Wiring .................................................................................. 9
Dispersion

Using space distribution units (SDU-E and SDU-I) ..... 11
Using dispersion tubes ................................................ 14
Using a RAPID-SORB

®

dispersion assembly ............. 16

Drip tee installation ...................................................... 17
Interconnecting piping tables ....................................... 18

Operation

Start-up procedures ........................................................... 19
Control ............................................................................... 20

Maintenance

Maintenance procedures ................................................... 21
Troubleshooting guide ....................................................... 24
Replacement parts ............................................................. 26

Warranty

........................................................................... 32

VM99-C-0302-M-0302.pdf 2

11/19/2009 9:51:07 AM

«
1
2
3
4
...
»

Summary of Contents for HUMIDI-TECH

































Reviews:

No comments

Related manuals for HUMIDI-TECH

Brand: AirTek Pages: 20

Brand: Gardner Denver Pages: 36

Brand: DriSteem Pages: 18

Brand: TaoTronics Pages: 12

Brand: HIdRos Pages: 56

SONOREX TECHNIK UT16

Brand: BANDELIN Pages: 18

Brand: Magnavox Pages: 6

Brand: Kiwi Pages: 16

Brand: Munters Pages: 32

Brand: Goldstar Pages: 12

Brand: Goldstar Pages: 12

Brand: Goldstar Pages: 24

Brand: Goldstar Pages: 27

Brand: Mitsubishi Pages: 20

Brand: Vortice Pages: 24

Brand: Quest Engineering Pages: 16

Brand: Qlima Pages: 88

Brand: babymoov Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands