DriSteem HUMIDI-TECH Installation, Operation And Maintenance Manual Download Page 3

Page: 3 / 32

HUMIDI-TECH

HUMIDIFIER OVERVIEW

Deionized water models
(HUMIDI-TECH DI)

The HUMIDI-TECH DI, shown here,
is specifically designed for use with
deionized or reverse osmosis water.

Standard water models
(HUMIDI-TECH)

The standard water HUMIDI-TECH unit
requires water conductivity of at least
100 µS/cm to operate. It will not
operate with water treated
by reverse osmosis or
deionization processes
(see DI water model below).

OM-82-4

Removable
evaporating
chamber

Slide assembly under evaporating chamber
provides easy removal for cleaning

INCOLOY alloy-sheathed
immersion heaters

Keyholes for
wall mounting

Water fill DN10
(3/8") (female)

DN40 or DN50 flexible
vapor hose, pipe or
tubing connects to
dispersion tube(s) or
to an SDU

Condensate
return line

Duct

Electrical area

Electrical conduit
knockouts

DN20 (¾") threaded
skimmer port and
overflow drain

Water fill access hole

Condensate
return line

Electrical area

Removable
evaporating
chamber

INCOLOY alloy-sheathed
immersion heaters

Duct

Electrical conduit knockouts

Slide assembly under
evaporating chamber provides
easy removal for cleaning

Water fill access hole

Keyholes for
wall mounting

Water fill DN10
(3/8") (female)

Float cutoff switch

OM-82-5

Ball valve

DN20 (¾") threaded skimmer
port and overflow drain

DN40 or DN50 flexible vapor
hose, pipe or tubing connects to
dispersion tube(s) or to an SDU

VM99-C-0302-M-0302.pdf 3

11/19/2009 9:51:07 AM

Summary of Contents for HUMIDI-TECH

































Search results

Summary of Contents for HUMIDI-TECH

Reviews:

Related manuals for HUMIDI-TECH

Brands by name

Popular brands

DriSteem HUMIDI-TECH, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for HUMIDI-TECH

Reviews:

Related manuals for HUMIDI-TECH

Brands by name

Popular brands