Dresser MOONEY FLOWGRID SLAM SHUT Installation, Operation & Maintenance Manual Download Page 18

Page: 18 / 20

Dresser

Vent Valve Disassembly and Assembly

Refer to Figure 16 for this operation.

1. Remove the stem retainer, stem, washer and spring from

the controller housing. Discard the o-ring and stem.

2. Lubricate and install a new o-ring on the valve stem

retainer.

3. Insert the long end of the stem into the retainer. Slide the

washer and then spring on the short end of the new stem.

4. Insert the stack into the controller housing and tighten to

120 to 130 inch-lbs.

Installation of the Cartridge

Refer to Figure 16 for this operation.

1. Start the cartridge into its bore.

2. Tighten the cartridge to 120 to 130 inch-lbs.

Spring Case Assembly

Refer to Figure 16 for this operation.

1. Install the diaphragm assembly into the diaphragm

counter bore.

2. Lubricate the depression in spring follower with

Lubriplate 105 or equivalent.

3. Place the spring for the set point range required on top of

the diaphragm assembly. Set the spring follower on top
of the spring.

4. Make sure the diaphragm assembly, spring and spring

follower are oriented correctly and install the spring case
with the bug vent facing forward. Install the four bolts and
torque to 120 to 130 inch-lbs.

Actuator Disassembly and Assembly

Refer to Figure 16 for this operation.

1. Remove the four cap screws, actuator cap, diaphragm,

restrictor pin and o-rings. Disassemble the diaphragm
assembly. Discard o-rings and diaphragm.

2. Remove the pawl lever actuator pin from the controller

housing. Discard the pin if damaged or worn. Install the
pin in the controller housing.

3. Lubricate the o-rings in the rebuild kit with the lubricant

provided.

4. Install an o-ring on the diaphragm bolt followed by the

diaphragm plate. Install a diaphragm on the diaphragm
retainer bolt. Make sure the convex side of the diaphragm
is toward the diaphragm plate.

5. Install the washer followed by the nut on the bolt and

torque the nut to 120 to 130 in-lbs.

6. Install an o-ring on each end of the restrictor pin. Install

the restrictor pin with the o-rings into the diaphragm cap.

7. Place the diaphragm assembly in the housing. Install the

diaphragm cap and torque the four screws to 120 to
130 inch-lbs.

Adjusting

Screw

Bug Vent

Cap

Screw

Spring
Follower

Main Spring

Spring
Housing

Nut

Controller
Housing

Spring

Case Label

Cartridge
Assembly

Controller
Label

Vent Spring

Washer

Plug & Stem

Vent Valve
Seat

Actuator Cap

Cap Screw

O-Ring

Plate

Washer

Restrictor
Pin

Nut

Stud

O-Ring

Bolt

Figure 16 – Controller Assembly

Summary of Contents for MOONEY FLOWGRID SLAM SHUT





















Search results

Summary of Contents for MOONEY FLOWGRID SLAM SHUT

Reviews:

Related manuals for MOONEY FLOWGRID SLAM SHUT

Brands by name

Popular brands

Dresser MOONEY FLOWGRID SLAM SHUT, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for MOONEY FLOWGRID SLAM SHUT

Reviews:

Related manuals for MOONEY FLOWGRID SLAM SHUT

Brands by name

Popular brands