background image

-

11

-

Appendix 1: Troubleshooting

1) In the period of using Smart series microscope, if there is any trouble occurs, please referring to

the following sheet listed some common troubleshooting resolve them.

Trouble

Causation

Remedy

Switch on but bulb dark

Plug is unreliable

Plug in again

Bulb is broken

Change bulb

Fuse is broken

Change fuse

Bulb is flickering or

brightness is unsteady

Bulb is unstable

Insert it again

Bulb is broken

Replacing bulb

Brightness of view field

isn’t enough or is uneven

Bulb specification doesn’t

meet the requirement

Replacing bulb

Brightness isn’t adjusted

correctly

Adjust rotation

potentiometer

Objective isn’t in correct

position

Make the objective in correct

position

The size of iris aperture is too

small

Adjust the size of iris aperture

Brightness of view field

isn’t enough or is uneven

Lens (objective, eyepiece,

condenser, light collector) has

dust

Clean it

Position of condenser is too low Higher condenser

Image isn’t clear

(contrast or definition

isn’t enough)

Cover glass of specimen

doesn’t meet the requirement

Use required thickness cover

glass (0.17mm)

Cover glass of specimen isn’t in

up direction

Place specimen correctly

Surface of objective lens

Is dirty (especially it is easy for

the front lens of 40

×

objective

to dip in immersion oil)

Clean it

Immersion oil isn’t used for

100

×

objective (oil)

Use immersion oil

Immersion oil doesn’t meet the

requirement

Use immersion oil

supplied by us

There is bubble in immersion oil Clear the bubble way
Size of iris aperture isn’t

proper

Adjust the size of iris

aperture

Position of condenser is too low Readjust the position of

condenser

One side of image is

dark or image is

moving as focusing

Objective isn’t in correct

position

Make the objective in

correct position

Specimen isn’t placed correctly Place specimen levelly on stage

and clip it with clamp

Objective touches

specimen as changing low

times objective to high

times objective

Cover glass of specimen isn’t in

up direction

Place specimen correctly

Cover glass doesn’t meet the

requirement

Use required thickness

cover glass (0.17mm)

Image observed by two

eyes aren’t in

superposition entirely.

Interpupilary distance isn’t

adjusted correctly.

Adjust interpupilary

distance according to two eyes

It is easy for eyes to be

tired during observing

Diopter isn’t adjusted correctly Readjust diopter

2) If there is any trouble occurs in digital system , please referring to the following sheet listed some
common troubleshooting resolve them.

Summary of Contents for SMART-e Series

















Reviews: