background image

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-5RE Modular Revolving Nosepiece                

   

 

Page 1 of 18 

 

 

Revision 3 

Complete Teardown, Cleaning, and 

Reassembly of the Olympus BH2-5RE 

Modular Revolving Nosepiece 

Revision 3 

 

Copyright © 2018, 2020, 2021 Carl Hunsinger 

All  rights  reserved.    This  document  may  not  be  reproduced  or  distributed,  in  whole  or  in  part,  for  any  commercial 
purpose  without the express  written consent of the author (

[email protected]

).  Permission is hereby granted to 

distribute this PDF document in its entirety for personal, non-commercial purposes only, provided that the contents are 
not modified in any way, including the copyright notices contained herein.  This document may be freely distributed on 
WWW,  FTP,  or  BBS  sites  in  accordance  with  these  restrictions.    The  content  of  this  document  is  provided  for 
informational  purposes  only,  with  no  expressed  or  implied  warranties  whatsoever,  including,  but  not  limited  to, 
function, suitability, safety, accuracy, or completeness of information. 

Revision History

 

Revision 

Description of Changes 

Date 

Initial release 

June 25, 2018 

Show worn mechanical detents 

July 13, 2020 

Common formatting, minor changes 

May 19, 2021 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for BH2-5RE



















Reviews: