Draper 64261 Instructions Manual Download Page 4

- 2 -

- 3 -

POWER SUPPLY

CONNECTING YOUR MACHINE TO THE POWER SUPPLY: 230V

To eliminate the possibility of an electric shock, your machine has been fitted with a BS approved,
non rewireable moulded 3 pin plug and cable which incorporates a fuse, the value of which is
indicated on the pin face of the plug. Should the fuse need to be replaced an          approved
BS1362 fuse must be used of the same rating, marked thus          .

The fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse
cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e.
red). Fuse covers are available from your Draper Tools stockist.

If the fitted plug is not suitable, it should be cut off and destroyed. *The end of the cable should
now be suitably prepared and the correct type of plug fitted. See below.

WARNING: THIS APPLIANCE IS DOUBLE INSULATED.

Blue – Neutral, Brown – Live.
As these colours may not correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter
‘N’ or coloured black or blue.
The wire which is coloured brown must be connected to the terminal which is marked with the
letter ‘L’ or coloured red or brown

*WARNING:

A plug with bare flexible wires exposed is hazardous if engaged in a live power socket outlet.

WARNING: THIS APPLIANCE MUST BE EARTHED.
Green and Yellow - Earth, Blue - Neutral, Brown - Live.
As these colours may not correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:

The wire which is coloured green and yellow must be connected to the terminal in the plug which
is marked with the letter ‘E’ or by the earth symbol

or coloured green or green and yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter
‘N’ or coloured black or blue.

The wire which is coloured brown must be connected to the terminal which is marked with the
letter ‘L’ or coloured red or brown.

N.B.

Three phase machines must be connected by a qualified electrician.

EXTENSION LEAD CHART:
Extension lead sizes shown assure a voltage drop of not more than 5% at rated load of tool.

Ampere rating

3

6

10

13

(on Name plate)

7.5m

0.75

0.75

1.0

1.25

15m

0.75

0.75

1.0

1.5

22.5m

0.75

0.75

1.0

1.5

30m

0.75

0.75

1.25

1.5

45m

0.75

1.25

1.5

2.5

Extension Cable Length

Wire Size mm

2

Summary of Contents for 64261













Reviews: