Dräger Polytron 7500 Instructions For Use Manual Download Page 30

Page: 30 / 72

Fault – Cause – Remedy

Page 30 of 72 Pages

9023927 - 2nd edition - May 2007

# 120

The sensor has been exposed to an exces-
sively high gas concentration for a long
period.

Reduce the exposure to high gas concentrations. If the
problem persists, ﬁt a new sensor, page 23.

# 131

Bad sensor, no longer operating.

Replace the sensor, page 23.

# 132

Electrolyte liquid evaporates. Measure-
ments are no longer possible.

If the problem persists, ﬁt a new sensor, page 23.

# 135

Information such as the Part No. and the
Serial No. is not available.

Disconnect the unit from the mains and restart it.
If this error occurs again: Have the Polytron 7500 checked
by DrägerService.

Fault

Cause

Remedy

LED »

« lights

red

The pyrolysis oven is defect

Replace the pyrolysis oven, page 26.

LED »

« lights

red

Fault in measurement branch –
pump measurement branch defect

Check the hose connections for blockages.
Replace the pump, page 25.

LED »

« ﬂashes

red

An internal ﬂow test is being carried out –
this is not a fault

– – –

LED »

« lights

red

Fault in principal branch –
pump principal branch defect

Check the hose connections for blockages.
Replace the pump, page 25.

All three LEDs
»

«, »

« and

« lights or

ﬂashes red

Electronic defect

Polytron 7500 to be repaired by Service of Dräger Safety.

Warning number

Cause

Remedy

Summary of Contents for Polytron 7500









































































Search results

Summary of Contents for Polytron 7500

Reviews:

Related manuals for Polytron 7500

Brands by name

Popular brands

Dräger Polytron 7500, Instructions For Use Manual

Search results

Summary of Contents for Polytron 7500

Reviews:

Related manuals for Polytron 7500

Brands by name

Popular brands