Dräger Polytron 7500 Instructions For Use Manual Download Page 12

Page: 12 / 72

Installing Dräger Polytron 7500

Page 12 of 72 Pages

9023927 - 2nd edition - May 2007

Installing the Dräger Polytron 7500

●

Unpack the Dräger Polytron 7500.

●

Remove the cover of the Polytron 7500. To do this

gently pull apart the cover on both sides and

lift upwards.

●

Fit the Polytron 7500 using the metal hooks into the slots provided on the docking
station.

●

Slide cover back over the installed Polytron 7500 until it snaps into place at the
sides.

●

Connecting the hoses:
Insert the hose into the quick release fastener below the unit.

Gas input from the inlet point right connection (marked with O-ring).

Gas output to the offtake left connection.

●

Check the hoses to make sure they are inserted properly

Attention! The electrical connection via the edge connector must be clean,
i.e. the safety hooks (3) underneath must snap into the docking station.

Attention! No cables or internal hoses must be pinched.

00623927_1.eps

3927_1

.eps

0082392

7_1

.eps

Summary of Contents for Polytron 7500









































































Search results

Summary of Contents for Polytron 7500

Reviews:

Related manuals for Polytron 7500

Brands by name

Popular brands

Dräger Polytron 7500, Instructions For Use Manual

Search results

Summary of Contents for Polytron 7500

Reviews:

Related manuals for Polytron 7500

Brands by name

Popular brands