DR 11.5 Chipper Shredder Safety & Operating Instructions Manual Download Page 28

Page: 28 / 36

11.5 CHIPPER SHREDDER

Chapter 6: Parts Lists and Schematic Diagrams

Parts List – Hopper, Chute and Discharge

Note:

Part numbers listed are available through DR Power Equipment.

Ref# Part#

Description

11076

Nut, Nylon Lock, 5/16-18, ZP

39283

Label, Danger, Discharge

38640

Bolt, HCS, 5/16-18 X 6", GR5, ZP

36521

Bolt, Hex Flange, 1/4-20 X 5/8", GR5, ZP

33331

Nut, Nylon Lock, Flanged, 1/4-20

6 38671 Chute

w/Labels,

Chipper

7 38648 Guard,

Chipper

8 38647 Plate,

Guard

Ref# Part#

Description

39282

Label, Danger, Safety

34141

Label, DR Logo, 5.75" Silver

38676

Hopper w/Labels, Shredder

12 36525

Guard,

Shredder

36544

Support, Guard, Hopper

36526

Support, Hopper Guard

15 36515

Plate,

Blowback

16 38656

Deflector,

Discharge

Summary of Contents for 11.5 Chipper Shredder





































Search results

Summary of Contents for 11.5 Chipper Shredder

Reviews:

Related manuals for 11.5 Chipper Shredder

Brands by name

Popular brands

DR 11.5 Chipper Shredder, Safety & Operating Instructions Manual

Search results

Summary of Contents for 11.5 Chipper Shredder

Reviews:

Related manuals for 11.5 Chipper Shredder

Brands by name

Popular brands