background image

6

 

        

DR

® 

9.5 Chipper Shredder

 

California Proposition 65: 

 

Engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other 
reproductive harm. 

 

This product contains or emits chemicals known to the State of California to cause cancer, birth defects, and other 
reproductive harm. 

General Safety (continued) 

California Proposition 65 

A Note to All Users  

Under California, Washington, New Mexico law, and the laws of some other states, you are not permitted to operate an internal 
combustion engine using hydrocarbon fuels without an engine spark arrestor.  This also applies to operation on US Forest Lands. 

If you live in a location that requires a Spark Arrestor please call us at (800) 376-9637 and we will provide one free of charge. 

Failure of the owner or operator to maintain their equipment in compliance with state regulations is a misdemeanor and may be 
in violation of other state and/or federal regulations.  Contact your State Park Association or the appropriate state organization for 
specific information in your area. 

No list of warnings and cautions can be all-inclusive.  If situations occur that are not covered by this manual, the operator must 
apply common sense and operate this DR 9.5 Chipper Shredder in a safe manner.  Contact us at www.DRpower.com or call Toll 
Free: 1-800-DR-OWNER (376-9637) for assistance. 

 

Never try to pick up, move, or transport the machine while the Engine is running or the Flywheel is turning.  

 

For safe loading up ramps carefully PULL the machine with the Shredder Hopper hand holds.  For safe unloading down 
ramps, guide the machine from behind with the hand holds so it goes down the ramps and you follow. 

 

Before performing any maintenance or inspection procedure on the Chipper Shredder, shut the Engine OFF, wait 5 minutes 
for machine to cool, remove the Spark Plug Wire keeping it away from the Spark Plug. 

 

Never allow people who do not understand and/or have not read this Safety and Operating Instructions Manual to use the 
Chipper Shredder.  Allow only responsible individuals who are familiar with these rules of safe operation to use your machine. 

 

Never overload or attempt to Chip or Shred material beyond the manufacturer’s recommendation.  Personal injury or damage 
to the machine could result. 

 

While using the Chipper Shredder, don't hurry or take things for granted.  When in doubt about the equipment or your 
surroundings, stop the machine and take the time to look things over. 

 

Never operate the machine when under the influence of alcohol, drugs, or medication. 

 

Use the machine only in daylight. 

 

Stay alert for hidden hazards or traffic. 

 

Keep all nuts and bolts tight and keep the equipment in good operating condition. 

Summary of Contents for DR 9.5

































Reviews: