background image

discrimination display and the depth display are offset due to soil
impacts during field detection.The composition, size, and oxidation of
the underground metal will also affect the display results.When the
operator chooses to exclude a certain metal or judge whether there is a
valuable metal, to fully consider these factors, do not "exclude" the
valuable metal.

Caution
1)In busy traffic places, please do not use headphones in case of
accidents.
2)Do not break into private homes without permission.
3)Avoid areas where power lines, cables, or pipes may be buried,
especially for placing flammable gases and liquids.
4)Do not detect in military areas where bombs or gas explosives may be
buried.
5)When excavating the target, use reasonable methods and do not
destroy the vegetation. After the excavation, the original surface state
should be restored.

Troubleshooting Guide
symptom

resolvent

No power, the LCD has no
indication, no boot sound.

1. Ensure that the battery is
installed correctly
2. Replace the battery

Continuous hair "DI" "DI" sound

1. Determine if other metal
detectors are working nearby
2. Reduce the sensitivity
appropriately

The LCD showed normal, but had
no detectable function

The connection to the search coil
is poor. Check the cable is Plugged
in correctly.

LCD showed normal, but showed
low detection sensitivity

When turning on, there may be
metal near the search coil. Ensure

Summary of Contents for MT-XE


























Reviews: