background image

T

RITON

 S

YSTEMS

9

9640-

TO

-9600

C

ONVERSION

 P

ROCEDURE

Slowly extend the slide tray on the rails. Stop when
the rails are fully extended. This is the service position
for the slide tray.

5.

Place Dispenser Mechanism on slide tray, allowing
enough space at the rear of the mechanism to allow
access to the control board.  Do not slide the
mechanism under the rear tabs on the tray until
directed to do so in a later step!

6.

Plug the Dispenser Power Cable (09600-00013) into
the mating connector (PL2) also located on the back
of the dispenser. Make sure the DC power cable
is plugged into the mating connector properly
before proceeding
.

7.

Plug the Dispenser Data Cable (09600-00027) into
the mating DB25 connector (PL6) located on the back
of the dispenser, using a small flat head screwdriver.

Slide Tray installed. Shown in  service
position

Place dispenser mechanism on slide
tray.

Dispenser mechanism on slide tray.
Do not slide mechanism under rear
tabs until power and data cables have
been connected!

Attach power cable to dispenser control
board.

Attach data cable to dispenser control
board.

Location of slide tray tabs.

Summary of Contents for Triton 9600











Reviews: