Dover Anthony 401 Service & Installation Instructions Download Page 46

Page: 46 / 80

Model 401 & 403 Pass-Thru

Service and Installation Instructions

99-21972-S001 Rev. C

- 46 -

www.anthonyintl.com

401 LED Lighting

Center Fixture (60-21817-xxxx)

End Fixture (60-21818-xxxx)

Description

Center Fixture (4000K)

60” Fixture

60-21817-0002

Description

Left End Fixture (4000K)

60” Fixture

60-21818-0002

Description

Right End Fixture (4000K)

60” Fixture

60-21818-1002

New Driver Installation

1. When installing the new driver, keep in mind to make sure black and white

wires (power) are pointed toward the top of the frame.

2. Remove the Mullion cover using a flat screwdriver.

3. Remove the raceway cover by inserting a flat screwdriver into the seam

between the metal raceway and the plastic cover and prying it open.

4. Using two #8 tapping screws, install the driver just below all cables, no

farther than half way down inside the mullion.

NOTE: Installer may have to drill two holes in raceway to accommodate

LED power supply if the door is not an Anthony model.

Summary of Contents for Anthony 401

















































































Search results

Summary of Contents for Anthony 401

Reviews:

Related manuals for Anthony 401

Brands by name

Popular brands

Dover Anthony 401, Service & Installation Instructions

Search results

Summary of Contents for Anthony 401

Reviews:

Related manuals for Anthony 401

Brands by name

Popular brands