Dover Anthony 401 Service & Installation Instructions Download Page 21

Page: 21 / 80

Model 401 & 403 Pass-Thru

Service and Installation Instructions

99-21972-S001 Rev. C

- 21 -

www.anthonyintl.com

Model 401 Frame Installation

Read instructions completely before installing frames.

Openings must conform to net openings listed in Price Book or other.

Check size of finished frame to net opening.

Do not force frame into tight opening.

Check net opening for plumb and square as shown below. Sill must be
level left to right and front to back.

a. Jambs, header and sill should be wood for a secure installation.

b. Anthony door frame needs a sill of at least 1-1/2

” for proper

installation.

HEADER

CAULKING- REAR VIEW

SEAL FRAME TO WALL MOUNT FROM REAR

CASE
STRUCTURE
FRAME

CAULKING

AROUND CASE

STRUCTURE

HEADER
FRAME

PLUMB

VERTICALLY

CORRECT MOUNT

SQUARE

MEASURE FROM

CORNER TO CORNER

SILL
FRAME

REAR

SILL

FRONT

CROSS SECTION

Frame Installation

Set frame in opening. For safety, partially install wood screws into top of frame.

Do not tighten. Torquemaster (silver rectangular box) goes at bottom of frame.
Hinge pin to top of frame.

Frame

Torquemaster

Anchor

Hole

Screw (2 Required)

Threshold

Pass-Thru Cross-Section (with/without Threshold)

Summary of Contents for Anthony 401

















































































Search results

Summary of Contents for Anthony 401

Reviews:

Related manuals for Anthony 401

Brands by name

Popular brands

Dover Anthony 401, Service & Installation Instructions

Search results

Summary of Contents for Anthony 401

Reviews:

Related manuals for Anthony 401

Brands by name

Popular brands