DÖRR EcoGun AS MAN DC Operation Manual Download

Page: 26 / 56

Fault description

Cause

Remedy

Worn out seal kit (24).

Replace seal kit.

7.2 “Cleaning”

Warning tone or alarm on the
electrostatic controller (if paint
supply for non-flammable paints
is isolated)

Basic housing (23) con-
taminated with paint

Clean basic housing.

7.2 “Cleaning”

Paint hose contaminated
with paint

Clean paint hose.

Spray distance is too
close

Increase spray distance or

decrease voltage value.

Water build-up in the air
ducts of the basic
housing

Drain water on the mainte-

nance unit. Blow out the air

ducts.

Grounded object near
the paint supply

Ensure minimum distance of

300mm between isolated paint

supply and grounded objects.

Worn out seal kit (24).

Replace seal kit.

9.3.1 “Replace needle,

nozzle and seal kit”

9.3

Troubleshooting

9.3.1 Replace needle, nozzle and seal kit

Personnel:

Operator
+ additional qualification high tension
technology
+ additional qualification explosion pro-
tection

Protective equipment:

Protective workwear
Eye protection
Anti-Static Safety Boots

Requirements:

The spray gun is disassembled

10.2

“Disassembly”.

Disassembly

Fig. 25: Ground electrode

Faults

11/2019

EcoGun AS MAN DC - MSG00023EN

26/56

Summary of Contents for EcoGun AS MAN DC

























































Search results

Summary of Contents for EcoGun AS MAN DC

Reviews:

Related manuals for EcoGun AS MAN DC

Brands by name

Popular brands

DÖRR EcoGun AS MAN DC, Operation Manual

Search results

Summary of Contents for EcoGun AS MAN DC

Reviews:

Related manuals for EcoGun AS MAN DC

Brands by name

Popular brands