background image

Operation & Maintenance Manual

Foreword

Information

The Contents Of This Manual Are Considered To Be Proprietary And Confidential To Doosan
Infracore Portable Power (Herein Referred To As “Portable Power”), And Should Not Be
Reproduced Without The Prior Written Permission Of Portable Power.

Nothing Contained In This Document Is Intended To Extend Any Promise, Warranty Or
Representation, Expressed Or Implied, Regarding The Portable Power Products Described
Herein. Any Such Warranties Or Other Terms And Conditions Of Sale Of Products Shall
Be In Accordance With The Standard Terms And Conditions Of Sale For Such Products,
Which Are Available Upon Request.

This Manual Contains Instructions And Technical Data To Cover All Routine Operation And
Scheduled Maintenance Tasks By Operation And Maintenance Staff. Major Overhauls Are
Outside The Scope Of This Manual And Should Be Referred To An Authorized Portable
Power Service Department.

All Components, Accessories, Pipes, And Connectors Added To The Compressed Air
System Should Be:

Of Good Quality, Procured From A Reputable Manufacturer And, Wherever
Possible, Be Of A Type Approved By Portable Power.

Clearly Rated For A Pressure At Least Equal To The Compressor Safety Valve
Setting.

Compatible With The Compressor Oil.

Accompanied With Instructions For Safe Installation, Operation, And Maintenance.

Details Of Approved Equipment Are Available From The Portable Power Service
Departments. The Use Of Repair Parts Other Than Those Included Within The Approved
Parts List May Create Hazardous Conditions Over Which Portable Power Has No
Control. Therefore, Portable Power Cannot Be Held Responsible For Equipment In Which
Non-Approved Repair Parts Are Installed.

Portable Power Reserves The Right To Make Changes And Improvements To Products
Without Notice And Without Incurring Any Obligation To Make Such Changes Or Add Such
Improvements To Products Sold Previously.

The Intended Uses Of This Compressor Are Outlined Below And Examples Of Unapproved
Usage Are Also Given. However, Portable Power Cannot Anticipate Every Application Or
Work Situation That May Arise.

If In Doubt, Consult Supervision

.

This Compressor Has Been Designed And Supplied For Above Ground Operation To Be
Used For Compression Of Normal Ambient Air Containing No Additional Gases, Vapors, Or
Particles Within The Ambient Temperature Range Specified In The General Data Section
Of This Manual.

6

Summary of Contents for P250/HP210WKUB-EX-T2








































































Reviews: