Doosan P250/HP210WKUB-EX-T2 Operation And Maintenance Manual Download | Manualshive

Page: 56 / 71

background image

Lubrication

Operation & Maintenance Manual

Compressor Oil Chart

Refer to this chart for the correct compressor oil required. Note that the selection of oil is
dependent on the rated operating pressure of the compressor and the ambient temperature
expected to be encountered before the next oil change.

Note: Oils listed as “preferred” are required for extended warranty.

Compressor oil carryover (oil consumption) may be greater with the use of alternative
oils.

Rated Operating

Pressure

Ambient

Temperature

Compressor Oil Specification

100 psi to 300 psi

-10°F to 125°F

(-23°C to 52°C)

Preferred:

PRO-TEC™

Alternate:

ISO Viscosity Grade 46 with rust and
oxidation inhibitors, for rotary screw
compressor service.

350 psi

(-23°C to 52°C)

(-10°F to 125°F)

65°F to 125°F

(18C°C to 52°C)

Preferred: PRO-TEC™

XHP605

Alternate:

XHP405

ISO Viscosity Grade 68 Group 3 or
5 with rust and oxidation inhibitors
designed for air compressor service.

Preferred:

XHP605

XHP1001

Preferred Oil - Use of these oils with Doosan branded filters can extend airend warranty.
Refer to the warranty policy for details or contact your representative.

Preferred Oil

1 gal. (3.8

Liter)

5 gal. (19.0

Liter)

55 gal. (208

Liter)

220 gal. (836

Liter)

Pro-Tec™

36899698

36899706

36899714

36899722

XHP605

-

22252076

22252050

22252068

XHP1001

-

35612738

35300516

-

XHP405

-

22252126

22252100

22252118

Engine Oil

54480918

36875938

36866903

-

55

«
...
54
55
56
57
58
...
»

Summary of Contents for P250/HP210WKUB-EX-T2








































































Reviews:

No comments

Related manuals for P250/HP210WKUB-EX-T2

Brand: Gardner Denver Pages: 60

Brand: EarthLinked Pages: 35

Brand: Quincy Pages: 12

Brand: LACAIR Pages: 16

Brand: California Pages: 17

Brand: Danfoss Pages: 26

Brand: WilTec Pages: 8

Brand: WilTec Pages: 9

Brand: WilTec Pages: 10

Brand: WilTec Pages: 12

ECO Scroll Series

Brand: FScurtis Pages: 40

Brand: Sparmax Pages: 32

Brand: Sound Skulptor Pages: 12

Bock HG8 Series

Brand: GEA Pages: 8

Brand: Xiaomi Pages: 207

Brand: Parkside Pages: 73

Brand: Parkside Pages: 88

Brand: Kaishan Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands