background image

Factory Direct Tractors

Technical Maintenance

14.  Inspect  hydraulic  hoses  and  rams  for  leaks 

and repair as required.

15.  Inspect  machine  for  loose  or  broken  bolts, 

tighten or replace as required.

16. Check brake and clutch adjustment and adjust 

as  required.  Request  technical  support  if  unsure 

how to carry out adjustments.

7.2.5   250 Hourly service

1. Change engine oil and filter.

2. Change injector pump oil.

3. Change front diff and final drive oils.

4. Change hydraulic steering oil and clean 
strainer.

5. Change gearbox oil and replace filter.

6. Grease loader pins, pedal shafts, tie rod ends, 

king  pins,  drive  shafts,  steering  stops  and  water 

pump bearings (if grease nipple fitted).

7.  Check  wheel  nut  tension  and  tyre  pressures, 

adjust as required.

8. Check tappet clearance and adjust as required.

9. Check air filter and dust bowl for contaminant 

and clean as required, replace every 50 hours in 

very dusty conditions. Inspect inlet manifold and 

hoses for leaks, repair as required.

10.  Drain  coolant,  flush  cooling  system and  refill 

with new coolant.

11.  Inspect  radiator  core  for  blockage,  blow  out 

and reinspect, clean as required.

12.  Inspect  machine  for  loose  or  broken  bolts, 

tighten or replace as required.

13. Inspect engine, transmission and final drives 

for oil leaks and repair as required.

14. Check brake and clutch adjustment and adjust 

as  required.  Request  technical  support  if  unsure 

how to carry out adjustments.

7.2.6   500 Hourly service

1. Change engine oil and filter, check oil pressure 

relief valve and adjust as required.

2. Change fuel filter and clean inline strainer.

3. Change injector pump oil, check spill timing and 

adjust as required.

4. Change front diff and final drive oils.

5. Change hydraulic steering oil, clean strainer and 

refill with new oil.

6. Change gearbox oil and filter, flush transmission 

housing and refill.

7. Grease loader pins, pedal shafts, tie rod ends, 

king  pins,  drive  shafts,  steering  stops  and  water 

pump bearings (if grease nipple fitted).

8.  Check  wheel  nut  tension  and  tyre  pressures, 

adjust as required.

9. Check tappet clearance and adjust as required.

10. Check air filter and dust bowl for contaminant 

and clean as required, replace every 50 hours in 

very dusty conditions. Inspect inlet manifold and 

hoses for leaks, repair as required.

11.  Drain  coolant,  flush  cooling  system  and  refill 

with new coolant.

12.  Inspect  radiator  core  for  blockage,  blow  out 

and reinspect, clean as required.

13.  Inspect  machine  for  loose  or  broken  bolts, 

tighten or replace as required.

14. Inspect engine, transmission and final drives 

for oil leaks and repair as required.

15. Check brake and clutch adjustment and adjust 

as  required.  Request  technical  support  if  unsure 

how to carry out adjustments.

7.2.7   1000 Hourly service

1. Change engine oil and filter, check oil pressure 

relief valve and adjust as required.

2. Change fuel filter and clean inline strainer.

3. Change injector pump oil, check spill timing and 

adjust as required.

4. Change front diff and final drive oils.

5.  Change  hydraulic  steering  oil,  clean  strainer, 

refill with oil.

6. Change gearbox oil and filter, flush transmission 

housing, and refill.

7. Grease loader pins, pedal shafts, tie rod ends, 

king  pins,  drive  shafts,  steering  stops  and  water 

pump bearings (if grease nipple fitted).

8.  Check  wheel  nut  tension  and  tyre  pressures, 

adjust as required.

9. Check tappet clearance and adjust as required.

10. Check air filter and dust bowl for contaminant 

and clean as required, replace every 50 hours in 

very dusty conditions. Inspect inlet manifold and 

hoses for leaks, repair as required.

11.  Drain  coolant,  flush  cooling  system  and  refill 

with new coolant.

12.  Inspect  radiator  core  for  blockage,  blow  out 

and reinspect, clean as required.

13.  Inspect  machine  for  loose  or  broken  bolts, 

tighten or replace as required.

14. Inspect engine, transmission and final drives 

for oil leaks and repair as required.

15. Check brake and clutch adjustment and adjust 

as  required.  Request  technical  support  if  unsure 

7-3

Summary of Contents for ZB25

















































































































Reviews: