background image

TRANSMITTER SOLUTIONS WARRANTY

The warranty period of this product is 12 months from the purchasing 

date. During this period, if the product does not operate correctly due 

to a defective component, the product will be repaired or replaced at 

the sole discretion of Transmitter Solutions. This warranty does not 

extend to the product’s casing, which can be damaged by conditions 

outside of the control of Transmitter Solutions.

EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES 

NO WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, 

INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS 

FOR A PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY 

REPRESENTATION OF TRANSMITTER SOLUTIONS, EXPRESS OR IMPLIED, 

WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”. 

TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION 

THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS 

A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS 

SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, 

INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO 

PERSONS OR PROPERTY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS 

A RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD TRANSMITTER 

SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, 

MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS. 

BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS

TERMS IN CONSIDERATION OF RECEIVING THE GOODS.

Summary of Contents for dolkpl1kb













Reviews: