manualshive.com logo in svg

Dok PPC-1000, Technical Description And Operations Manual

Share
Download
Dok PPC-1000 Technical Description And Operations Manual Download Page 6

 

PPC-1000    Rev.1.0 

6 of 29

 User 

Manual 

© DOK Ltd (Mm-wave Division of ELVA-1 ltd), 2005-2006. All rights reserved. 

For installations in all other countries, implement protection in accordance with the 
safety standards and regulatory requirements of the country where the equipment is to 

be installed. 

•

 

Do not install or operate this equipment in the presence of flammable gases or fumes. 

Operation of any electrical instrument in such an environment constitutes a definite 
safety hazard. 

•

 

Do not install substitute parts or perform any unauthorized modification to the 

equipment. Changes or modifications not expressly approved by Elva-1 Millimeter Wave 
Division void the Elva-1 Millimeter Wave Division Warranty on the equipment. 

 

Equipment Precautions 
 

CAUTION! 

This product is designed to withstand moisture conditions typically encountered when installed 
outdoors. This is not designed for operation under water. 
 
This product is not designed to withstand direct thunderbolt. It should be operated only under 

protection of external lightning rod. 

 

This product should be operated only from the type of power source indicated on the unit or in 

manual. 
 
 
 

Summary of Contents for PPC-1000






























Reviews:

No comments

Brands by name

Popular brands

Load more brands