manualshive.com logo in svg

Dok PPC-1000, Technical Description And Operations Manual

Share
Download
Dok PPC-1000 Technical Description And Operations Manual Download Page 12

 

PPC-1000    Rev.1.0 

12 of 29

 User 

Manual 

© DOK Ltd (Mm-wave Division of ELVA-1 ltd), 2005-2006. All rights reserved. 

 

 

4.4

 

Alignment Tools 

The following tools should be on hand when running the alignment of the radio system: 

•

 

Wrench 8 mm & 17 mm (item 17) 

•

 

Hose clip, 50-70 mm (item 8) 

 
 

4.5

 

Equipment assembling  

Both radios equipped with 6

1

 long shipping bolts (see 

photos from part 4.2 Equipment Unpacking). 
 
Replace the shipping bolt placed near the “Ground” mark 

with a set #15, observing the items order.  The Radio 
flanges should be placed between contact strips. 

Connect the grounding wire to the bolt as shown on the 
photo. 
 
Replace the rest 5 shipping bolts with bolts, nuts, 
washers and tightening washers (set #14). 
 

                                          

1

 The exact number of the bolts used for shipping purpose may differ. 

Summary of Contents for PPC-1000






























Reviews:

No comments

Brands by name

Popular brands

Load more brands