manualshive.com logo in svg

Dok PPC-1000, Technical Description And Operations Manual

Share
Download
Dok PPC-1000 Technical Description And Operations Manual Download Page 13

 

PPC-1000    Rev.1.0 

13 of 29

 User 

Manual 

© DOK Ltd (Mm-wave Division of ELVA-1 ltd), 2005-2006. All rights reserved. 

 
 
 
 

4.6

 

Diam. 60 cm antennas assembling 

60 cm antennas come in separate box. To assemble antennas, do the following: 

•

 

Set included joint scaling strip into the flange seal groove 

•

 

Remove top covers from antenna and the Radio flanges 

•

 

Match antenna and radio flanges, according to waveguide orientation 

•

 

Fix an antenna on the radio with 6 bolts, washers and tightening washers, included in 
the complete set 

 

CAUTION! 

Fixing 60 cm antennas, observe waveguide orientation, paying attention that wave-guide-fed 

slot orientation on antenna matches the orientation of the waveguide on radio case. Otherwise 
the Bridge will not operate properly. 
 

CAUTION! 

During antenna assembling, take precautions against ingress of dirt, dust and moisture into 
antenna and Radio waveguides. 
 

4.7

 

Radio on-table testing after unpacking (optional)  

After the unpacking and antenna assembling of the radios, you could test the radios on-table 
before installing them at their principal location (mast; tower; roof of the building). This is an 

optional operation but after the test you will be sure that radios works OK and there are no 
malfunction because of the damage during transportation. The test includes only parameter 

diagnostics. The main data communication channel will not be tested at this moment. 
 
You will need a stand-alone notebook or desktop PC with installed LAN card to display test 
results through SNMP. The following software has to be installed at this computer: 
1. Moxa NE SDK Manager  
2. ELVA PPC Monitor 
 
The Moxa NE SDK Manager is third-party software which you can use in accordance with End 
User License. You are provided with your copy of this software because of partnership between 

ELVA-1 and Moxa. 
ELVA PPC Monitor is ELVA-developed SNMP monitor apps.  
 
Please do not distribute these software applications outside your organization without written 

permission of ELVA-1. 
 
You can download both software apps from the following location 

http://www.elva-1.com/download/PPC/NE_Cdrom.zip

 (8M) 

http://www.elva-1.com/download/PPC/PPC.zip

 (150K)  

 
By default, both radios have the same IP-address: 192.168.127.254 

•

 Click 

Network Connection – Properties - IP protocol – Properties

 on your stand-alone computer to 

set up a temporal IP address for this computer from the same subnet as radio default IP address. 

Summary of Contents for PPC-1000






























Reviews:

No comments

Brands by name

Popular brands

Load more brands