background image

6

MN1617

A3

Unit Size

Reduction Stage

Pints

Liters

38

2

1.7

0.8

3

1.7

0.8

48

2

3.0

1.4

3

3.2

1.5

58

2

4.6

2.2

3

4.8

2.3

68

2

5.9

2.8

3

6.1

2.9

88

2

14.2

6.7

3

13.7

6.5

108

2

18.8

8.9

3

19.2

9.1

128

2

30.0

14.2

3

31.5

14.9

148

2

46.1

21.8

3

46.1

22.3

168

2

67.8

32.1

3

69.1

32.7

A3

Unit 

Size

Reduction 

Stage

Input 

Reducer 

Pints

Input 

Reducer 

Liters

Primary 

Reducer 

Pints

Primary 

Reducer 

Liters

68

4

0.8

0.4

6.6

3.1

5

1.3

0.6

6.6

3.1

88

4

1.5

0.7

13.6

6.4

5

3.2

1.5

13.6

6.4

108

4

1.5

0.7

18.7

8.8

5

3.2

1.5

18.7

8.8

128

4

3.1

1.5

31.0

14.7

5

3.2

1.5

31.0

14.7

148

4

3.1

1.5

46.9

22.2

5

3.2

1.5

46.9

22.2

168

4

3.1

1.5

68.5

32.4

5

5.3

2.5

68.5

32.4

Motorized Shaft Mount (MSM) Reducers and Integral Gearmotors

These mounting arrangements are for all output configurations and output shaft types.
IMPORTANT: When ordering, please specify mounting position for correct oil quantity. In cases of mounting position other than 

shown here with regard to the oil quantity, please reference the Incline Mounting page in the Quantis Engineering Catalog, and contact 

Application Engineering.

NOTE: The oil volumes shown are approximate values and cannot be used to correctly set the reducer oil level. ALWAYS fill 

the reducer to the correct oil level plug and recheck in 1 week.

A3 – Horizontal – Ceiling Mount

Oil Level

Ventilation

Oil Drain

Sensor

NOTES:

All MSM 38 units are sealed for life and furnished with only one plug for filling and draining.

4 and 5 stage reduction reducer consists of two reducers assembled to each other, the Input Reducer and the Primary Reducer. The reducers are 

sealed from each other and require different oil levels per the chart.

* Hole location on opposite side of reducer.

A

A

*

*

A

A

**

**

Summary of Contents for Quantis MSM

















Reviews: