manualshive.com logo in svg

Dodge 2014 dodge charger, Owner'S Manual

The 2014 Dodge Charger Owner's Manual is an essential guide for every Dodge Charger owner, providing detailed information and instructions for the vehicle's features, maintenance, and troubleshooting. Download this manual for free from manualshive.com and empower yourself with all the necessary knowledge to enhance your driving experience.

Share
Download
background image

may need to recline the seat and/or raise the head
restraint to get a better fit. If the rear seat can be moved
forward and rearward in the vehicle, you may wish to
move it to its rear-most position to make room for the
child seat. You may also move the front seat forward
to allow more room for the child seat.

4. Attach the lower hooks or connectors of the child

restraint to the lower anchorages in the selected seat-
ing position.

5. If the child restraint has a tether strap, connect it to the

top tether anchorage. See the section “Installing Child
Restraints Using the Top Tether Anchorage” for direc-
tions to attach a tether anchor.

6. Tighten all of the straps as you push the child restraint

rearward and downward into the seat. Remove slack
in the straps according to the child restraint manufac-
turer’s instructions.

7. Test that the child restraint is installed tightly by

pulling back and forth on the child seat at the belt
path. It should not move more than 1 inch (25.4 mm)
in any direction.

How To Stow An Unused ALR Seatbelt

When using the LATCH attaching system to install a child
restraint, stow all ALR seat belts that are not being used by
other occupants or being used to secure child restraints. An
unused belt could injure a child if they play with it and
accidentally lock the seatbelt retractor. Before installing a
child restraint using the LATCH system, buckle the seat
belt behind the child restraint and out of the child’s reach.
If the buckled seat belt interferes with the child restraint
installation, instead of buckling it behind the child re-
straint, route the seat belt through the child restraint belt
path and then buckle it. Do not lock the seatbelt. Remind
all children in the vehicle that the seat belts are not toys and
that they should not play with them.

88

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 2014 dodge charger


































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 dodge charger

Jeep Renegade Owner'S Handbook Manual preview
Renegade
Brand: Jeep Pages: 212
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Brand: Mazda Pages: 400
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Brand: Cadillac Pages: 368
Luverne 205760 Installation Instructions preview
205760
Brand: Luverne Pages: 3
Navman B2+ User Manual preview
B2+
Brand: Navman Pages: 27
Würth 071554055 User Instructions preview
071554055
Brand: Würth Pages: 36
Whispbar K919W Fitting Instructions Manual preview
K919W
Brand: Whispbar Pages: 17
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Brand: Safe Fleet Pages: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Brand: Honda Pages: 4
RAM 1500 2WD 2021 Owner'S Manual preview
1500 2WD 2021
Brand: RAM Pages: 496
KEKO K617 Installation Description preview
K617
Brand: KEKO Pages: 3
Movon MDAS-5 Installation Manual preview
MDAS-5
Brand: Movon Pages: 43
WABCO TP19039 Manual preview
TP19039
Brand: WABCO Pages: 34
Honda 08B15-SDN-100 Installation Instructions Manual preview
08B15-SDN-100
Brand: Honda Pages: 22
Mercedes-Benz 2013 CL Operator'S Manual preview
2013 CL
Brand: Mercedes-Benz Pages: 494
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Brand: Dometic Pages: 24

Brands by name

Popular brands

Load more brands