Dodge 2010 Ram Truck Chassis Owner'S Manual Download Page 559

Page: 559 / 610

Chassis

Component

Fluid, Lubricant, or Genuine Part

Automatic Transmission

MOPAR

威

ATF+4

威

Automatic Transmission Fluid or equivalent licensed

ATF+4

威

product.

Transfer Case

MOPAR

威

ATF+4

威

Automatic Transmission Fluid or equivalent licensed

ATF+4

威

product.

Transfer Case – NVG 246 Only

MOPAR

威

NVG 246 Automatic Transmission Fluid or equivalent.

Front Axle – 1500 Four-Wheel Drive
Models

GL-5 SAE 75W-90 (MS-9763) or equivalent.

Rear Axle – 1500 Models

MOPAR

威

Synthetic Gear Lubricant SAE 75W-140 (MS-8985). Limited-Slip

Rear Axles require the addition of 118 ml (4 oz.) MOPAR

威

Limited Slip

Additive or equivalent.

Front and Rear Axle – 2500/3500
Models

Synthetic, GL-5 SAE, 75W-90 or equivalent. Limited-Slip 10.5/11.5 inch
Rear Axles

Limited slip additive is not required.

Brake Master Cylinder

MOPAR

威

DOT 3 and SAE J1703 or equivalent. If DOT 3 brake fluid is not

available, then DOT 4 is acceptable. Use only recommended brake fluids.

Power Steering Reservoir

MOPAR

威

Power Steering Fluid +4, MOPAR

威

ATF+4

威

Automatic Trans-

mission Fluid or equivalent licensed ATF+4

威

product.

558

MAINTAINING YOUR VEHICLE

Summary of Contents for 2010 Ram Truck Chassis



































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2010 Ram Truck Chassis

Reviews:

Related manuals for 2010 Ram Truck Chassis

Brands by name

Popular brands

Dodge 2010 Ram Truck Chassis, Owner'S Manual

Search results

Summary of Contents for 2010 Ram Truck Chassis

Reviews:

Related manuals for 2010 Ram Truck Chassis

Brands by name

Popular brands