Dodge 2010 Ram Truck Chassis Owner'S Manual Download Page 447 | Manualshive

Page: 447 / 610

background image

Weight Ratings)” for the website address that contains
the necessary information for your specific drivetrain.

Trailer Hitch Classification Definitions

Class

Max. Trailer Hitch Industry

Standards

Class I - Light Duty

2,000 lbs (907 kg)

Class II - Medium
Duty

3,500 lbs (1587 kg)

Class III - Heavy Duty

5,000 lbs (2268 kg)

Class IV - Extra
Heavy Duty

10,000 lbs (4540 kg)

Fifth Wheel/
Gooseneck

Greater than 10,000 lbs

(4540 kg)

Refer to the “Trailer Towing Weights (Maximum
Trailer Weight Ratings)” for the Maximum Gross
Trailer Weight (GTW) towable for your given drive-
train.

All trailer hitches should be professionally installed on
your vehicle.

Trailer Towing Weights (Maximum Trailer Weight
Ratings)

NOTE:

For additional trailer towing information in-

cluding maximum trailer and tongue weight rating for
your vehicle, refer to the following website addresses:

•

http:// www.dodge.com/bodybuilder

.

•

http:// www.dodge.ca

(Canada).

Trailer and Tongue Weight

Always load a trailer with 60% to 65% of the weight in
the front of the trailer. This places 10% to 15% of the GTW
on the tow hitch of your vehicle. Loads balanced over the
wheels or heavier in the rear can cause the trailer to sway

severely

side to side which will cause loss of control of

the vehicle and trailer. Failure to load trailers heavier in
front is the cause of many trailer accidents.

446

STARTING AND OPERATING

«
...
445
446
447
448
449
...
»

Summary of Contents for 2010 Ram Truck Chassis



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Ram Truck Chassis

Brand: Hama Pages: 2

Brand: RaceChip Pages: 20

2012 Escalade Hybrid

Brand: Cadillac Pages: 90

Brand: Mobile Create Pages: 15

Brand: Kargo Master Pages: 6

Brand: Fast Master Products Pages: 13

Brand: Fab Fours Pages: 13

Brand: RBO Pages: 15

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

Brand: Ford Pages: 40

Brand: Axxess Pages: 16

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brand: Reliant Pages: 116

Brand: Kuda Pages: 3

Brand: BrandMotion Pages: 12

Brand: injen technology Pages: 3

Brand: Opel Pages: 233

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands