manualshive.com logo in svg

DKS 6500 Series, Owner'S Manual

The InfoPrint 6500 Series is a versatile, high-performance printer designed for businesses. To assist users in optimizing its functionalities, a comprehensive User Manual is available for download, free of charge, from our website. Discover all the features and functions of this exceptional product through our easy-to-access manual.

Share
Download
background image

4

6500-065-K-7-08

Gate Construction

Instructions regarding intended installation:

Vehicular gates should be constructed and installed in accordance with ASTM F2200; Standard Specification for Automated 
Vehicular Gate Construction. For a copy of this standard, contact ASTM directly at 610-832-9585; [email protected]; or 

www.astm.org

.

Important Safety Instructions

WARNING - To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with gate controls. Keep the remote control away from children.
3. Always keep people and objects away from gate. 

NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.

4. Test the operator monthly. The gate MUST reverse on contact with a rigid object or stop or reverse when an object    
  activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust  
  and retest the gate operator properly can increase the risk of injury or death.
5. Use the emergency release only when the gate is not moving.
6. KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person make repairs to gate  
 hardware.
7. The entrance is for vehicles only. Pedestrians must use separate entrance.
8. 

SAVE THESE INSTRUCTIONS!

•

 Install the gate operator only if:

    1. The operator is appropriate for the construction of the gate and the usage class of the gate.
    2. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet  
      (1.22 m) above the ground to prevent a 2 ¼ inch (57.2 mm) diameter sphere from passing through the openings  
      anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open position.
    3. All exposed pinch points are eliminated or guarded.
    4. Guarding is supplied for exposed rollers. 

•

 The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate  

  access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that  
  persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate. 

•

 The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures  

  when opening and closing to reduce the risk of entrapment. Swinging gates should not open into public access areas.

•

 The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. Do not  

  over-tighten the operator clutch, pressure relief valve or reduce reversing sensitivity to compensate for a damaged gate.

•

 For gate operators utilizing Type D protection:

    1. The gate operator controls must be placed so that the user has full view of the gate area when the gate is moving.
    2. A warning placard shall be placed adjacent to the controls.
    3. An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed.
    4. No other activation device shall be connected.

•

 Controls intended for user activation must be located at least ten feet (10’) away from any moving part of the gate and  

  where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or  
  easily accessible controls should have a security feature to prevent unauthorized use.

•

 The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset control shall not   

  cause the operator to start.

•

 A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.

•

 For gate operators utilizing a non-contact sensor: 

    1. See the instructions on the placement of non-contact sensors for each type of application.
    2. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate  
      is still moving in the opening direction.
    3. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exist, such as the  
      perimeter reachable by a moving gate or barrier.

Summary of Contents for 6500 Series

















































Reviews:

No comments

Related manuals for 6500 Series

CAME FAST Series Installation Manual preview
FAST Series
Brand: CAME Pages: 16
CAME BK Series Installation, Operation And Maintenance Manual preview
BK Series
Brand: CAME Pages: 17
CAME OPP Series Installation, Operation And Maintenance Manual preview
OPP Series
Brand: CAME Pages: 64
CAME FROG series Manual preview
FROG series
Brand: CAME Pages: 16
CAME FROG series Instructions preview
FROG series
Brand: CAME Pages: 2
CAME FROG series Installation Instructions Manual preview
FROG series
Brand: CAME Pages: 32
CAME KRONO KR300 Installation Instructions Manual preview
KRONO KR300
Brand: CAME Pages: 32
CAME RLB Quick Start Manual preview
RLB
Brand: CAME Pages: 2
4Ddoors SOLAR GA201 Instructions For Fitting, Operating And Maintenance preview
SOLAR GA201
Brand: 4Ddoors Pages: 26
fadini APROLI 280 BATT Instruction Manual preview
APROLI 280 BATT
Brand: fadini Pages: 12
fadini Elpro S50-T1 Manual preview
Elpro S50-T1
Brand: fadini Pages: 24
MyQ LiftMaster 84501 User Manual preview
LiftMaster 84501
Brand: MyQ Pages: 40
Doit Security+ 4200DI Owner'S Manual preview
Security+ 4200DI
Brand: Doit Pages: 40
CAME BX10 Installation Manual preview
BX10
Brand: CAME Pages: 36
Delton PL500 User Manual preview
PL500
Brand: Delton Pages: 14
Normstahl Ultra excellent Installation Instructions Manual preview
Ultra excellent
Brand: Normstahl Pages: 20
Normstahl EasyLift 500 Translation Of The Original Operating Manual preview
EasyLift 500
Brand: Normstahl Pages: 56
SkylinkHome Houselink 318STR Quick Manual preview
Houselink 318STR
Brand: SkylinkHome Pages: 2

Brands by name

Popular brands

Load more brands