DKS 6500 Series Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 48

background image

29

6500-065-K-7-08

SECTION 5 - OPTIONAL CONVENIENCE OPEN ADJUSTMENTS

The optional convenience open system installed in your vehicular gate operator is designed as a convenience enhancement only.
It is not designed or intended to provide continuous gate operation during a power outage. Its sole purpose is to provide a
method to open the vehicular gate to allow unimpeded traffic flow when the gate and access control system is without power. If
your access control system requires 100% power backup and continuous operation when primary (AC) power has failed, a
power inverter / backup system, such as DoorKing’s Model 2000, is required.

•

The convenience open system cannot provide continuous gate operation during a power outage.

•

This system cycles the gate to the open position one time only after AC power failure.

•

The convenience open system requires testing on a monthly basis to insure the batteries are fully charged and that the

system is operational.

•

The convenience open system uses two 12-volt, 3.0 amp-hour gel-cell batteries. These batteries should be replaced

every two years on average, or sooner if required.

•

Batteries are affected by temperature. Cold temperatures will reduce the effectiveness of the batteries. High temperatures

will result in a shortened battery life.

•

Batteries are not covered under warranty.

This convenience open system consist of a control board (2340-010), motor and power supply (batteries) providing a
completely redundant drive system to open the gate should a power outage occur. This system is not designed to maintain
continuous gate operation; rather it provides a convenient method to open a gate

ONCE

during adverse conditions. If continu-

ous gate and access control system operation is required, refer to the DoorKing Model 2000 Inverter / Backup Power System.

5.1 Operating Mode

Turn switch 1

ON

and the system will automatically

open the gate approximately 3 seconds after loss of
AC power. Automatic mode is

always

used for for

gates in general access applications such as gated
communities, apartment complexes, etc.
Switch 1

OFF

is not used.

Automatic Open after loss of AC Power

Once AC power is restored, the system’s control board
can be set to “

automatically re-key

” the gate operator

(switch 3

ON

) to establish normal operation, or can be

set to require a “

manual input

” (switch 3

OFF

) before

the operator resumes normal operation.

Restart Options once AC Power is restored

DIP-Switches

DIP-Switches

2340

«
...
29
30
31
32
33
...
»

Summary of Contents for 6500 Series

















































Reviews:

No comments

Related manuals for 6500 Series

Brand: Chamberlain Pages: 45

Brand: Portamatik Pages: 9

Brand: Primere Pages: 24

Brand: Optima Pages: 21

Brand: Calimet Pages: 24

Brand: Ginnys Pages: 8

Brand: Wisniowski Pages: 76

Brand: CAME Pages: 22

Brand: Key Automation Pages: 50

Brand: Ghost Controls Pages: 68

Brand: FAAC Pages: 19

Brand: Serai Pages: 12

MERCURIO 524A F

Brand: Serai Pages: 16

Brand: CAME Pages: 72

Brand: Vogue Pages: 28

Brand: GarageAce Pages: 16

Brand: Comunello Pages: 40

Brand: Wayne-Dalton Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands