DKS 6400 - UL 325 Class 1 Owner'S Manual Download | Manualshive

Page: 13 / 22

background image

6400-065-T-8-12

11

The fabricated U-channel will vary depending
on the width of the gate frame (

D

).

Installation of 6400 Continued

Gate Connection to 6400

Apply Grease

Grease
Filler
Hole

Weld
U-channel
on both
sides of
the gate.

Important:

The weight of the

gate

MUST NOT

rest on the 6400.

DO NOT

weld gate frame to U-Channel.

Protect the 2 release handles from
welding sparks during welding.

Release
Handle

Foundation Box

U-Channel Dimensions

After the foundation box has been mounted in concrete and the gate has been
connected to it, proceed to the next page to correctly orient drive motor and
install components in the foundation box.

1

5

3/4”

Gate Frame

U-Channel

D

D + 1”

1 1/2”

Min.

3/

8

” thick metal min.

Fabricated U-Channel

Gate A

rm

U-Channel

Gate Frame

«
...
11
12
13
14
15
...
»

Summary of Contents for 6400 - UL 325 Class 1























Reviews:

No comments

Related manuals for 6400 - UL 325 Class 1

Brand: tau Pages: 6

Brand: vds Pages: 41

Brand: Chamberlain Pages: 28

Brand: Chamberlain Pages: 2

Brand: CAME Pages: 2

Brand: FAAC Pages: 36

Security+ PD300D

Brand: Chamberlain Pages: 40

Brand: TdA Pages: 19

Brand: Novoferm Pages: 28

Brand: Novoferm Pages: 43

Brand: SEA Pages: 36

Brand: Chamberlain Pages: 40

Brand: Chamberlain Pages: 28

Brand: Dea Pages: 16

Brand: Garaga Pages: 2

Brand: Calimet Pages: 18

Brand: GATEXPERT Pages: 27

Brand: TdA Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands