Dixon Bayco FloTech FT555 Series Instruction Manual Download | Manualshive

Page: 18 / 30

background image

FloTech FT555 Automatic Truck Overfill System Tester

Page 18

10784PA Rev G

FT555 Truck Tester

Step 7)

Once the optic/5-wire portion of the test is complete,

disconnect the tester from the optic/5-wire socket.

Step 8)

Move the J-Slot Screws to match the configuration of the

thermistor/2-wire socket.

Step 9)

Connect the tester to the thermistor/2-wire socket. Press

and release the GO button to start the thermistor/2-wire portion of
the test.

The tester will automatically perform the ground bolt and/or pin
9/10 continuity, and/or Truck ID Module tests if these options are
activated and enabled in the set up screen.

Automatic Test

Thermistor Mode

Connect THERM socket

Press GO to Continue

Automatic Test

2-Wire Mode

Connect 2-Wire socket

Press GO to Continue

«
...
16
17
18
19
20
...
»

Summary of Contents for FloTech FT555 Series































Reviews:

No comments

Related manuals for FloTech FT555 Series

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: Wacker Neuson Pages: 62

GPSMAP 188 Sounder

Brand: Garmin Pages: 134

Brand: U-Line Pages: 9

Green Machine H-3518

Brand: U-Line Pages: 3

Brand: ValueStore US Pages: 2

Brand: VelociRAX Pages: 4

Brand: ABM Pages: 17

Brand: Össur Pages: 50

Brand: Össur Pages: 13

PRO-FLEX XC PXC0xyyz

Brand: Össur Pages: 68

Brand: Össur Pages: 25

Brand: Össur Pages: 2

Brand: Össur Pages: 18

i-Digits Quantum

Brand: Össur Pages: 337

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands