PROGRAMMING P
SERIES
Page 11 of 100
"RFRG"
- Refrigeration Summary Errors
Press select button 4 and the display shows one of the following:
-
"SENS"
, indicating the temperature sensor is defective or unplugged.
-
"COLD"
, indicating the cabinet temperature is 3
0
F below lower limit.
-
"HOT"
, indicating the cabinet temperature is 3
0
F above upper limit.
-
"CNPR"
, indicating the cooling system has failed to decrease temperature 1
0
F per hour
while the compressor is running.
"CPO" - COIN
PAYOUT
ROUTINE
This function allows you to dump coins from the coin mechanism.
Press select button 4 to enter mode and the lowest coin value dispensable will show on the display. If a coin
mech is not in the vender
“NOCM”
will be displayed.
Press select button 2 or 3 to scroll through the different coin values available.
Press and hold select button 4 to dump the coins whose value is shown on the display.
Press select button 1 will return to
"CPO"
.
Press select button 2 to scroll to the next routine.
"TUFL" - TUBE
FILL
ROUTINE
This function allows you to count the coins loaded in the top (separator) of the coin mech that will be routed to
an inventory tube. Press select button 4 to enter mode and the total number of the coin type being entered
will be displayed and counted in the vender controller as they are installed. If a coin mech is not in the vender
“NOCM”
will be displayed. The controller will inhibit the acceptance of any coin, which does not go to a tube
during this procedure. If a tube full status is detected, that coin type will be inhibited. When you finish loading
all coins:
- Press select button 1 to return to
"TUFL"
.
- Press select button 2 to scroll to the next routine.
"TEST" -
TEST ROUTINE
This function allows you to diagnose different functions of the vender.
Press select button 4 and the display will show
"VEND"
.
Press select button 2 or 3 to scroll through the test routines available.
Press select button 1 to return to
"TEST"
.
"VEND"
- Vend
Testing
This function allows you to test vend each column.
Press select button 4 and the display will show
"CO-1"
.
Press select buttons 2 or 3 to scroll through the columns available to run in motor test.
Press select button 4 to run the motor of the column displayed. The Display will show
“VEND”
and
the Motor will run until a product is dispensed or the motor cycles through the package set cycles
and determines column is sold out.
Press select button 1 will return to
"VEND"
.
Press select button 2 to scroll to next test mode.
"JOG"
-
Jog Test or Prime
This function allows you to test jog or prime each column.
Press select button 4 and the display will show
"CO-1"
.
Press select buttons 2 or 3 to scroll through the columns available to run in jog test.
Press select button 4 to select the column displayed and
“FOR”
is displayed.
Press select buttons 2 or 3 to scroll through
“FOR”
(forward),
“REV”
(reverse), and
“PRIM”
(prime)
motor direction.
Press select button 4 to jog/prime the selected motor in the displayed direction.
Press select button 1 will return to
"CO-X"
where
X
is the column that was previously tested.
Press select button 1 again will return to
"JOG"
.
Press select button 2 to scroll to next test mode.
Summary of Contents for DN504P
