PROGRAMMING P
SERIES
Page 10 of 100
"CHAR"
- Changer
Summary
Errors
Press select button 4 and the display will show one of the following:
-
"CC"
, indicating a changer communication error. (No communication for more than 2
seconds)
-
"TS"
, indicating a tube sensor error.
-
"IC"
, indicating an inlet chute blocked error (no coins sensed in acceptor for 96 hours).
-
"TJ##"
, indicating a tube jam error.
-
"CRCH"
, indicating a changer ROM check sum error (failed changer).
-
"EE"
, indicating excessive escrow attempts (more than 255 since last coin sensed).
-
"NJ"
, indicating a coin jam reported by coin mech.
-
"LA"
, indicating a low coin acceptance rate (less than 80%).
-
"DIS"
, indicating an acceptor is unplugged.
-
"ROUT"
, indicating a coin was misrouted.
Press select button 1 will return to
"CHAR"
if all changer errors have not been cleared.
If all changer errors have been cleared the next error code will be displayed or
"NONE"
if there are
no errors.
Press select button 1 will return to
"EROR"
.
"BUAL"
-
Bill Validator Summary Errors
Press select button 4 and the display will show one of the following:
-
"BC"
, indicating a bill validator communication error. (No communication for more than 5
seconds)
-
"BFUL"
, indicating the bill stacker is full.
-
"BILL"
, indicating a defective motor in the validator.
-
"BJ"
, indicating a bill jam in the validator.
-
"BRCH"
, indicating a check sum error.
-
"BOPN"
, indicating an open stacker.
-
"BS"
, indicating a bill validator sensor error.
Press select button 1 will return to
"BUAL"
if all changer errors have not been cleared.
If all validator errors have been cleared the next error code will be displayed or
"NONE"
if there are
no errors.
Press select button 1 will return to
"EROR"
.
"CRDR"
-
Card Reader Summary Errors
Press select button 4 and the display will show one of the following:
-
"CRC"
, indicating no card reader communication for 5 seconds.
-
"CRXY"
, indicating the most recent "non-transient error" from the card reader (failed card
reader).
Press select button 1 will return to
"CRDR"
if all changer errors have not been cleared.
If all card reader errors have been cleared the next error code will be displayed or
"NONE"
if there
are no errors.
Press select button 1 will return to
"EROR"
.
Press select button 2 will scroll to the next routine.
"S-D"
– Display Device Summary Errors
Press select button 4 and the display will show one of the following:
-
"SDC"
, indicating no display device communication for 5 seconds.
-
"SDXX"
, error code number
“XX”
.
Press select button 1 will return to
"S-D"
if all display device errors have not been cleared.
If all display device errors have been cleared the next error code will be displayed or
"NONE"
if there
are no errors.
Press select button 1 will return to
"EROR"
.
Press select button 2 will scroll to the next routine.
Summary of Contents for DN504P
