![background image](http://html1.mh-extra.com/html/dixie-narco/dncb-501e/dncb-501e_technical-manual_2511149006.webp)
INSTALLATION & SETUP
5
TO OPEN THE PEPSI ELECTRONIC DOOR
LOCK:
1. Plug the vender into a properly powered
outlet.
2. Hold the key FOB 0 to 3 inches to the right
side of select button #10 and press the
button on the key FOB.
Note: The wide end of the FOB should
face the door.
3. The lock will begin releasing the door. The
display will indicate
Door opening.
After the motor has stopped running, you
can pull the door open. The display will
indicate:
Door unlocked
.
TO CLOSE THE PEPSI ELECTRONIC DOOR
LOCK:
CAUTION: DO NOT SLAM THE DOOR CLOSED.
Slamming the door closed can damage the
electronic locking device.
1. Push the door to the cabinet until the lock
motor starts. The display will indicate:
Door
closing
.
2. Continue to push the door for approximately
2 to 3 seconds after the lock motor starts.
The lock will pull the door closed tightly.
3. When the lock motor stops the door will be
locked and the display will indicate
: Door
locked
.
Before leaving the vender, ensure that the
door is locked.
The electronic door lock assembly is supplied by Tri
Teq Lock and Security. Dixie-Narco, Inc. does not
carry parts for the Tri Teq Electronic Door Lock.
For parts and assistance, please contact:
Tri Teq
701 Gullo
Elk Grove Village, IL 60007
Tel: 847-640-7002
Fax: 847-640-7008
Email: [email protected]
PLACING THE VENDER ON LOCATION
!! CAUTION !!
DO NOT TRANSPORT THE
VENDER TO OR FROM THE
LOCATION LOADED WITH
PRODUCT.
DAMAGE TO THE VENDER MAY
RESULT.
The vender must be located on a solid, flat, and
level surface. The vender must be positioned close
enough to an electrical outlet that an extension cord
is not required. If the machine will be subject to user
misuse or vandalism, it is recommended that the
vender be secured to the floor or wall as described
in Dixie-Narco Technical Bulletin 344. Call the Dixie-
Narco Technical Service Department or your Dixie-
Narco Representative for assistance.
LEVEL THE VENDER
When the vender is level, the door can be opened to
any position and it will not move by itself. Open the
door to several different positions before deciding
the vender is level. A carpenter’s level will help
verify the machine is level.
Make sure that all leveling legs are in contact with
the floor. If you cannot level the vender in its current
location, select another location. DO NOT place any
objects under the machine.
DANGER
THE VENDER MUST BE
PROPERLY LOCATED AND
LEVELED. IF THE MACHINE WILL
BE SUBJECT TO USER MISUSE
OR VANDALISM IT IS
RECOMMENDED THAT THE
VENDER BE SECURED TO THE
FLOOR OR WALL AS DESCRIBED
IN DIXIE-NARCO TECHNICAL
BULLETIN 344 TO MINIMIZE THE
RISK OF INJURY OR DEATH
FROM TIPPING.. CALL THE DIXIE-
NARCO TECHNICAL SERVICE
DEPARTMENT OR YOUR DIXIE-
NARCO REPRESENTATIVE FOR
ASSISTANCE.
SPACE THE VENDER
Do not block the rear of the vender. Keep the vender 4
inches (10 mm) from the wall to ensure adequate airflow
to the condenser and compressor. At the front of the
vender, make sure that nothing obstructs the air intake at
the bottom of the main door. At the rear of the vender,
make sure nothing obstructs the air exhaust at the bottom
of the cabinet.
Summary of Contents for DNCB 501E
