Dixie Narco DNCB 501E Technical Manual Download

Page: 29 / 85

TROUBLESHOOTING FLOWCHARTS

These charts are intended to isolate and correct most problems you might encounter.

ALL COINS ARE REJECTED

All coins are rejected.

Main Power

Disconnected.

Apply power

Blown Fuse

Check fuses and

replace if

necessary.

Loose connection.

Check cable at

coin mech and

controller board.

Jammed coin

mechanism.

Clear coins.

Weak springs on

changer gate.

Replace spring.

Acceptor gate partially

open.

Clean and reset

acceptor gate.

Dirty / faulty coin sensor.

Clean / Replace.

Incompatible coin

mechanism.

Replace with

approved coin

mechanism.

Defective coin

mechanism.

Replace with

known good

coin mechanism.

HT2 defective Universal

controller board or

HT3 Control Board.

Replace.

Check Prices

Reset Price

Check mech in

diagnostics

"Coin Mech".

Check reject

button / lever for

proper

adjustment.

Summary of Contents for DNCB 501E






















































































Search results

Summary of Contents for DNCB 501E

Reviews:

Related manuals for DNCB 501E

Brands by name

Popular brands

Dixie Narco DNCB 501E, Technical Manual

Search results

Summary of Contents for DNCB 501E

Reviews:

Related manuals for DNCB 501E

Brands by name

Popular brands