background image

 

Universal-XR 

                     5/17 

UXR01212015_REV1.4mm 

 

    

 

Installation and Operating Instructions 

Description 

Label 

Adjustment Range 

tC1 

tC2 

tC3 

tC4 

tC5 

tC6 

tC7 

Door open 

 compressor / fan status 

ODC 

No (0) = No change 

FAn (1) = Fan off 

CPr (2) = Compressor off 

F_C (3) = Compressor & Fan off 

Defrost relay configuration 

OAA 

Alr (0) = Alarm; 

db (1) = Dead Band; 

AUS (2) = Auxiliary; 

CP2 (3) = Second compressor output; 

liG (4) = Light output; 

dF2 (5) = Second defrost output. 

dEF (6) =1

st

 Defrost output 

Fan (7) =Fan output 

 

 

 

 

Auxiliary relay configuration 

OAB 

Alr (0) = Alarm; 

db (1) = Dead Band; 

AUS (2) = Auxiliary; 

CP2 (3) = Second compressor output; 

liG (4) = Light output; 

dF2 (5) = Second defrost output. 

dEF (6) =1

st

 Defrost output 

Fan (7) =Fan output 

Alarm relay polarity 

AOP 

Cl (0) = [11 -12] closed with alarm 

oP (1) = [11 -12] open with alarm 

Exclude temperature alarm - door open 

DOT 

0 to 255 min 

20 

20 

20 

20 

20 

20 

20 

Restart regulation with door open alarm 

RRD 

n (0) = No 

Y (1) = Yes 

Probe selection for Condenser Alarm 

AP2 

nP (0) =No Probe selected 

P1 (1) =Probe 1 
P2 (2) =Probe 2 

P3 (3) =Probe3 

Low temperature alarm of condenser 

AL2 

-55 to 150°C; 

-67 to 302°F 

-40°C; 

-40°F 

-40°C; 

-40°F 

-40°C; 

-40°F 

-40°C; 

-40°F 

-40°C; 

-40°F 

-40°C; 

-40°F 

-40°C; 

-40°F 

High temperature alarm of condenser 

AU2 

-55 to 150°C; 

-67 to 302°F 

110°C; 

230°F 

110°C; 

230°F 

110°C; 

230°F 

110°C; 

230°F 

110°C; 

230°F 

110°C; 

230°F 

110°C; 

230°F 

Differential for temperature condenser 
alarm recovery 

AH2 

0.1 to 25.5°C; 

1 to 45°F 

5°C; 

5°F 

5°C; 

5°F 

5°C; 

5°F 

5°C; 

5°F 

5°C; 

5°F 

5°C; 

5°F 

5°C; 

5°F 

Condenser temperature alarm delay 

AD2 

0 to 254 min, 255 = nU 

15 

15 

15 

15 

15 

15 

15 

Condenser temperature alarm exclusion at 
start up 

DA2 

0 to 720 min, res. 10 min 

90 

90 

90 

90 

90 

90 

90 

Compressor off with low temperature alarm 
of condenser 

BLL 

n (0) = No 

y (1) = Yes 

Compressor off with high temperature 
alarm of condenser 

AC2 

n (0) = No 

y (1) = Yes 

Temperature deviation from normal 
Set Point during Energy Saving 

HES 

-30.0 to 30°C; 

-54 to 54°F 

0°C; 

0°F 

0°C; 

0°F 

0°C; 

0°F 

0°C; 

0°F 

0°C; 

0°F 

0°C; 

0°F 

0°C; 

0°F 

ON / OFF key enabling 

ONF 

nU (0) = Disabled 

OFF (1) = Enabled 

ES (2) = Energy saving 

Buzzer enabling 

BEN 

n (0) = Disabled 

Y (1) = Enabled 

Parameter table 

PTB 

For factory use only 

Software release number 

REL 

Read only 

Evaporator probe temperature 

DP2 

Read only 

 

 

 

Third probe temperature 

DP3 

Read only 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for UNIVERSAL XR60CX


















Reviews: