background image

dIXEL

dIXEL

dIXEL

dIXEL

    

Operating Instructions 

cod. 

cod. 

cod. 

cod. 1592017410

1592017410

1592017410

1592017410    

 

1592017410  XLH360 GB r1.0  15.04.2005.doc 

XLH360 

3/16 

1.

 

GENERAL WARNING 

1.1

 

PLEASE READ BEFORE USING THIS MANUAL 

 

This manual is part of the product and should be kept near the instrument for easy and quick reference. 

 

The instrument shall not be used for purposes different from those described hereunder. It cannot be used as a safety device. 

 

Check the application limits before proceeding. 

1.2

 

 SAFETY PRECAUTIONS 

 

Check the supply voltage is correct before connecting the instrument. 

 

Do  not  expose  to  water  or  moisture:  use  the  controller  only  within  the  operating  limits  avoiding  sudden  temperature  changes  with  high 
atmospheric humidity to prevent  formation of condensation 

 

Warning: disconnect all electrical connections before any kind of maintenance. 

 

Fit the probe where it is not accessible by the End User. The instrument must not be opened. 

 

In case of failure or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see address) with a detailed description of the 
fault. 

 

Consider the maximum current which can be applied to each relay (see Technical Data). 

 

Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without crossing or intertwining. 

 

In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel with inductive loads could be useful. 

2.

 

GENERAL DESCRIPTION 

The 

XLH360

 is microprocessor controller, suitable for applications on medium or low temperature refrigerating units. It has 6 output relays to control 

compressor, heating elements, defrost/extractor fan, fan, de-humidifier/light and humidifier. It has 2 NTC inputs one for thermostat the other one for 
defrost. It’s also present a 4÷20mA input for humidity. There is one digital input (free contact) configurable by parameter. An  output allows the user 
to program the parameter list with the 

“Hot Key”.

 

3.

 

TEMPERATURE REGULATION 

The temperature regulation is performed through neutral zone using compressor and heater output relays. 

Set point

OFF

ON

 

• 

Heating

 output: CUT IN is “SET TEMP-dbt”, CUT OUT is when the temperature reaches the set point. 

• 

Compressor

 output CUT IN is “ SET TEMP +dbt”, CUT OUT is when the temperature reaches the set point. 

3.1

 

DEFROST  

During defrost the temperature control is disabled. 

 

If the second relay is configured as defrost: oA2=dEF

 then two defrost modes are available through the “

tdF

” parameter: defrost with electrical 

heater  (tdF=rE)  or  hot  gas  (tdF=  in).  The  defrost  interval  is  control  by  means  of  parameter  “

EdF

”: (EdF=in) the defrost is made every “

IdF

” time, 

(EdF=Sd)  the interval “IdF” is calculate through Smart Defrost algorithm (only when the compressor is ON). At the end of defrost dripping time is 
started, set by “

Fdt

” parameter. To 

disable 

the defrost set the 

MdF

 parameter to 

zero

 

 

If  oA2 is different from dEF, defrost is made only by stopping compressor  (tdF=rE). 
To disable 

 defrosts set 

MdF=0. 

 

Humidity regulation during defrost depends on the 

Hud 

parameter. 

With  

Hud=no

 humidity regulation is disabled.  

Con 

Hud=yES

 humidity regulation is performed also during defrost. 

 

4.

 

HUMIDITY REGULATION 

The humidity regulation is performed through neutral zone, by humidifying dehumidifying actions. 
Humidity control can be disabled setting the 

SET %RH to “nu”

 value. In this case only the temperature control is perform. 

4.1

 

HUMIDIFYING ACTION 

The humidifying action is done enabling the humidifier relay when the humidity is lower than the “SET %RH-dbH” value. 
The relay is switch off when humidity reaches the set values. 

Summary of Contents for 1592017410

















Reviews: