DIVEX MHE-02, Installation, Operating And Maintenance Manual

Page: 69 / 119

IMCB34-E1
2
2.2 Dimensions
*1 Rubber (optional)
*2 Up to four mounting brackets can be used.
For mounting of the instrument, panel thickness must be between 1 to 10 mm.
(When mounting multiple instruments close together, the panel strength should be
checked to ensure proper support.)
Waterproof and Dustproof are not effective when instruments are closely spaced.
2.3 Mounting Procedures
CB100
<Mounting Procedures>
1. Prepare the panel cutout as specified in 2.2 Dimensions .
2. Insert the instrument through the panel cutout.
3. Insert the mounting frame into the mounting from the rear of the instrument.
4. Push the mounting frame forward until the frame is firmly secured
to the panel. (Fig.1)
5. Fix the instrument to the panel by using the two screws. (Fig.2)
The optional waterproof/dustproof on the front of the instrument conforms to
IP66 when mounted on the panel. For effective waterproof/dustproof, the
gasket must be securely placed between instrument and panel without any
gap. If the gasket is damaged, please contact RKC sales office or the agent.
<Removal Procedures>
1. Turn the power OFF.
2. Remove the wiring.
3. Loosen the screw of the mounting frame.
4. Remove the mounting frame from the case. (Fig.3)
CB400/500/700/900
<Mounting Procedures>
1. Prepare the panel cutout as specified in 2.2 Dimensions .
2. Insert the instrument through the panel cutout.
3. Insert the mounting bracket into the mounting groove of the instrument.
Do not push the mounting bracket forward. (Fig. 1)
4. Secure the bracket to the instrument by tightening the screw. Take
care to refrain from moving the bracket forward.
5. Only turn about one full revolution after the screw touches the panel.
(Fig. 2)
If the screw has been rotated too tight, the screw may turn idle. In such
a case, loosen the screw once and tighten it again until the instrument is
firmly fixed.
6. The other mounting bracket should be installed in the same way as
described in
3. to 5.
When the instrument is mounted, always secure with two mounting brackets
so that upper and lower mounting brackets are positioned diagonally.
The optional waterproof/dustproof (CB900: mounting bracket 4 pieces)
on the front of the instrument conforms to IP65 when mounted on the
panel. For effective waterproof/dustproof, the gasket must be securely
placed between instrument and panel without any gap. If gasket is
damaged, please contact RKC sales office or the agent.
<Removal Procedures>
1. Turn the power OFF.
2. Remove the wiring.
3. Loosen the screw of the mounting bracket.
4. Hold the mounting bracket by the edge ( ) and tilt it ( ) to remove
from the case. (Fig. 3)
5. The other mounting bracket should be removed in the same way as
described in
3. and 4.
6. Pull out the instrument from the mounting cutout while holding the
front panel frame of this instrument. (Fig. 4)
Fig.3
Fig.1
Fig.2
When using the mounting
screws, only turn one full
revolution after the screw
touches the panel.
Screw
Mounting
frame
n : Number of controllers (2 to 6)
9.2
8.2 100
(Unit: mm)
1
(*1)
48
CB100
Individual Mounting
L1 48 n 3
25 45
0.6
0
25
Close vertical mounting
L1
0.6
0
25 45
0.6
0
L1
(Unit: mm)
CB400
Individual Mounting
Close vertical mounting
n : Number of controllers (2 to 6)
L1 48 n 3
0.6
0
9.2
8.2
1
100
(*1)
48
(Unit: mm)
CB700
n : Number of controllers (2 to 6)
Individual Mounting
Close vertical mounting
25
L1
68
0.7
0
L1 72 n 4
0.7
0
9.2
8.2 100
1 (*1)
72
30 92
0.8
0
(Unit: mm)
CB500
n : Number of controllers (2 to 6)
L1 48 n 3
Individual Mounting
Close vertical mounting
92
0.8
0
96
9.2
8.2
100
1 (*1)
n : Number of controllers (2 to 6)
L1 96 n 4
0.8
0
L1
(Unit: mm)
CB900
Individual Mounting
Close vertical mounting
25
92
0.8
0
96
*2
9.2
8.2 100
1 (*1)
Fig.2 Fig.1
Fig. 3
Fig. 4
Front panel
frame
Pull out
Panel