Ditch Witch ST37x Operator'S Manual Download

Page: 87 / 112

Service - 86

ST37x Operator’s Manual

1000 Hour

Change Engine Coolant

Drain cooling system at drain (2). Add approved
coolant at fill (1) every 1000 hours.

Adjust Valve Clearance

Adjust valve clearance every 1000 hours.

To adjust, see a certified Yanmar

engine technician.

Location

Task

Notes

Change engine coolant

Adjust valve clearance

Yanmar

certified technician

NOTICE:

•

The use of non-approved coolant may
lead to engine damage or premature
engine failure and will void engine
warranty.

•

See page 68 for list of approved coolants.

NOTICE:

If valve clearance is adjusted by anyone other than a certified Yanmar

engine technician,

engine warranties could be voided. Please see engine manual for more information.

t54om021h.eps

Summary of Contents for ST37x

















































































































Search results

Summary of Contents for ST37x

Reviews:

Related manuals for ST37x

Brands by name

Popular brands

Ditch Witch ST37x, Operator'S Manual

Search results

Summary of Contents for ST37x

Reviews:

Related manuals for ST37x

Brands by name

Popular brands