Ditch Witch ST37x Operator'S Manual Download

Page: 69 / 112

Service - 68

ST37x Operator’s Manual

Recommended Lubricants/Service Key

Engine Oil Temperature Chart

For more information on engine lubrication and maintenance, see your engine manual.

Approved Coolant

This unit was filled with coolant meeting Cummins

CES 14603 before shipment from factory. Add or

replace only with coolant meeting this specification, such as Fleetguard

ES Compleat coolant. This

coolant is available, pre-diluted, from your Ditch Witch

dealer as part number 255-1055. Contact your

Cummins service partner for a full list of approved coolants meeting CES 14603.

NOTICE:

•

Do not use water or high-silicate automotive-type coolant. This will lead to engine damage or
premature engine failure.

•

Do not mix heavy-duty diesel engine coolant and automotive-type coolant. This will lead to coolant
breakdown and engine damage.

Temperature range anticipated before next oil change

SAE 10W-30

SAE 5W-30

SAE 15W-40

SAE 20

SAE 30

t43om040w.eps

Summary of Contents for ST37x

















































































































Search results

Summary of Contents for ST37x

Reviews:

Related manuals for ST37x

Brands by name

Popular brands

Ditch Witch ST37x, Operator'S Manual

Search results

Summary of Contents for ST37x

Reviews:

Related manuals for ST37x

Brands by name

Popular brands