Ditch Witch ST37x Operator'S Manual Download

Page: 24 / 112

ST37x Operator’s Manual

Controls - 23

Graphic Display

Item

Description

Notes

High exhaust
temperature indicator

Indicates high exhaust
temperature.

IMPORTANT:

Will light when exhaust

cleaning (DPF regeneration) is
occurring.

Air filter restriction
indicator

Indicator will begin flashing
once the air filter is 25%
unrestricted. Percentage will
decrease as air filter
becomes more restricted.

For best results, replace filter
between 25% and 0%. Reset
after replacing air filter.

To view the air filter percentage before
25% unrestricted, press the
diagnostics menu button at any time.

Hydraulic fluid
temperature indicator

Lights and alarm sounds
when hydraulic fluid is
overheating.

Check hydraulic fluid level.

Reduce load.

Ensure oil cooler is clean.

Engine over-
temperature indicator

Flashes when temperature
rises above 230°F (110°C).

IMPORTANT:

If temperature goes

above 230°F (110°C):

1. Stop operation, set throttle to low
idle, and allow engine to cool.

2. Stop engine.

3. Check coolant level.

4. Ensure radiator is clean.

c00ic101w.eps

Summary of Contents for ST37x

















































































































Search results

Summary of Contents for ST37x

Reviews:

Related manuals for ST37x

Brands by name

Popular brands

Ditch Witch ST37x, Operator'S Manual

Search results

Summary of Contents for ST37x

Reviews:

Related manuals for ST37x

Brands by name

Popular brands