Directed Directechs DB3 Installation Manual Download Page 13

Page: 13 / 22

403.NISS3HT 3.09 2009 Nissan Altima (Smart Key)
© 2020-08-12 Directed. All rights reserved.

Connecting the module

Important!

Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior
to moving onto programming.

Warning!

To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application.

Flashing a module using your computer:
1.

Connect

the interface module to your computer using the

XKLoader2

to www.directechs.com using Internet Explorer, and

select

the Flash Module button.

Follow

the instructions to

select

your vehicle, installation type, and configure your options.

4. Once you have configured the firmware options,

click

on the FLASH button.

Flashing a module using your smartphone or tablet:
1.

Connect

the interface module to your

XKLoader3

Launch

the Directechs Mobile app on your smartphone or tablet.

Select

FLASH YOUR MODULE and

follow

the on screen instructions.

When the flashing operation is successful, you can proceed with the instructions below.

D2D installation

Recommended:

Connect

the 10-pin, 12-pin and 14-pin harnesses to the module, then

connect

the 4-pin D2D harness.

(14-pin)

(10-pin)

(D2D)

(12-pin)

W2W installation

If required:

Connect

the 10-pin and 12-pin harnesses to the module, then

connect

the 14-pin

harness to the module.

(14-pin)

(10-pin)

(12-pin)

Summary of Contents for Directechs DB3





















Search results

Summary of Contents for Directechs DB3

Reviews:

Directed Directechs DB3, Installation Manual, Page: 13 / 22

Search results

Summary of Contents for Directechs DB3

Reviews: