Directed 933.MIT3 Installation Manual Download Page 8

8

933.MIT3 2.11.195.3 2012 Mitsubishi Lancer Evolution
©2022 VOXX•DEI LLC.  All rights reserved.

Vehicle connections

The connection information listed below is specific to the 2012 Mitsubishi Lancer Evolution. Refer to “Pre-installation and application warnings” for a list of important notes.

Data harness, 8-pin white connector (H1)

Module

Connects To

Conn./Pin

Color

Description

Wire Location

(+/-)

Wire Color

Connection

H1/1

Tan

(Data) HS CAN Low 1

data link connector, black 16 pin plug, pin 14

data

violet

Mandatory

H1/2

Tan/Black

(Data) HS CAN High 1

data link connector, black 16 pin plug, pin 6

data

yellow/green

Mandatory

H1/3

Orange/Brown

(Data) HS CAN Low 2

Wireless Control Module on key switch, white 12 pin plug, pin 10

data

lt. green

Mandatory

H1/4

Orange/Green

(Data) HS CAN High 2

Wireless Control Module on key switch, white 12 pin plug, pin 11

data

yellow

Mandatory

H1/5

Lt. Green

No Connection

No Connection

H1/6

Violet/Brown

No Connection

No Connection

H1/7

Orange/Black

No Connection

No Connection

H1/8

Yellow/Black

No Connection

No Connection

Analog input/output harness, 22-pin white connector (H2)

Module

Connects To

Conn./Pin

Color

Description

Wire Location

(+/-)

Wire Color

Connection

H2/1

Lt. Green/Black

(-) Auto Headlight Shutoff Output

dash fuse box, brown 16 pin plug, pin 16

-

yellow

Remote Start

Only

H2/2

Blue/White

(-) Ground When Armed (GWA) Output 

[3]

Starter:
ignition switch, white 6 pin plug, pin 5
Ignition:
ignition switch, white 6 pin plug, pin 2
Must use a relay.
Must use a 1N4002 diode or larger.

+
+

orange (Lancer) or lt. blue
(Lancer Evolution)
white

Security Only

H2/3

Dk. Green/Black

(-) Lock Output

driver kick, white 25 pin plug, pin 7

-

red or yellow/red

Mandatory

H2/4

Red/White

(-) Trunk Release Output

No Connection

H2/5

Brown/Black

(-) Horn Output

horn switch or dash fuse box, white 19 pin plug, pin 19

-

green

Optional

H2/6

Brown/White

(-) AUX 1 Output

No Connection

H2/7

White

(+) Starter Output

Starter:
ignition switch, white 6 pin plug, pin 5
Clutch for manual Transmission:
clutch switch, white 2 pin plug, pin 2

+
+

orange (Lancer) or lt. blue
(Lancer Evolution)
black/red

Remote Start

Only

H2/8

Violet/Black

(+) Accessory Output

ignition switch, white 6 pin plug, pin 6

+

lt. green

Remote Start

Only

H2/9

Dk. Blue/Black

(-) Unlock Output

No Connection

H2/10

Lt. Blue/Black

(-) Factory Alarm Disarm Output

No Connection

H2/11

Brown/Red

(+) Siren Output 

[2]

Security Only

H2/12

Pink

(+) Ignition Sense Input

No Connection

H2/13

Violet

(+) Door Trigger Input

No Connection

H2/14

Brown

(+) Brake Input

No Connection

H2/15

White/Blue

(-) Activation Input

No Connection

Summary of Contents for 933.MIT3
























Reviews: