Directed 933.MIT3 Installation Manual Download Page 4 | Manualshive

Page: 4 / 23

Directed 933.MIT3 Installation Manual Download Page 4

4

933.MIT3 2.11.195.3 2012 Mitsubishi Lancer Evolution
©2022 VOXX•DEI LLC. All rights reserved.

Vehicle function compatibilities

This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.

Note

: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.

Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
Fuel level/EV battery level
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
Accessory Activation
Ignition Activation

RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Driver Door Pin
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
E-Brake Status
Ignition Status

«
...
2
3
4
5
6
...
»

Summary of Contents for 933.MIT3
























Reviews:

No comments